Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by ImTooOldForThis

  1. ImTooOldForThis

    "Format" BCM 400?

    Thank you!
  2. ImTooOldForThis

    "Format" BCM 400?

    Hi Guys Have a used BCM 400, full access as nnadmin just wondering if there is a way to "format" or reinstall the BCM 400 software to a fresh state using either element manager or a set? Thanks
  3. ImTooOldForThis

    bcm 200 or 400 ip phone licensing

    BCM.... complicated from 0x32 and 3x8 days :) On BCM 200 and 400 I know the digital stations are licensed requiring hardware, for IP phones is there license keys required to allow IP phones to connect or do the cabinets come ready to go for IP sets like the i2004?
  4. ImTooOldForThis

    Call Pilot 150 and BCM 200

    Hi, Migrating a system from Norstar with Call Pilot 150 to a BCM 200. Few questions: a) Can I connect the Call Pilot 150 to the BCM 200? b) If I have 20 mailbox licenses in the bcm 200 and 32 on the call pilot 150 existing unit, will all 52 be accessible when migrated? Thanks
  5. ImTooOldForThis

    Serial Connection to 11C

    Cancel the track down MAT Tools, dongle and a CD was in my laptop bag. (See = I'm too old for this) :)
  6. ImTooOldForThis

    Serial Connection to 11C

    Well..... I remember why I dislike computers, phones and telecom in general but have stuck with it for so long. I took the advice, ProComm seen carrier detect (CD) no issues, but only garbage on screen, checked baud rate, etc. No change. Tried alternate cable, same issue. So I disconnected...
  7. ImTooOldForThis

    Serial Connection to 11C

    Im just wondering, has anyone actually seen a computer (PC) console connected to an 11C cabinet to the cabinets 9 Pin male connector (so 9pin female - 9pin female cable) using just the 3 wires 2/3, 3/2, 5/5? I have wired new cables, tried existing cables, and as you can see tried every option...
  8. ImTooOldForThis

    Serial Connection to 11C

    No Change... Tried wiring 2 -> 6 6 -> 2 3 -> 3 So TX -> RX RX -> TX GND -> GND No change.
  9. ImTooOldForThis

    Serial Connection to 11C

    Hi Guys, Thats how shes been wired 2 ~~ 3, 3 ~~ 2, 5 ~~ 5, with and without null adapter. However, after looking at the paddle board PIN outs for the cabinet, Pin 5 is not used, Pin 2 is TX, Pin 3 GND, and Pin 6 RX, so to create a null modem 9pin - 9pin would I not cross Pins 2/6 and pass pin 3...
  10. ImTooOldForThis

    Serial Connection to 11C

    Hi, Yes 8 N 1 no flow control. SSC is at 9600 as is my terminal tried dropping down to 1200 also with no change. I am connected to the 9 pin male port from the cabinet that sits in the upper left not the port where the octopus cable would connect. This is the port that has always been...
  11. ImTooOldForThis

    Serial Connection to 11C

    Tried with caps on, I don't even get the ">" prompt it appears then goes to err200 code and won't come back or return even after hitting return.
  12. ImTooOldForThis

    Serial Connection to 11C

    Hi, Yes null modem has been used (tried cable and an adapter) TTY 0 is being used.
  13. ImTooOldForThis

    Serial Connection to 11C

    Additional: Did a reset with serial connected this is what appears in HyperTerm: AUD000 03 00AF LOAD 64 0 5 2 0 0 0 1824 00 0000 > XMI002 2 XDLC XMI002 9 XUT I have tried to type LOGI and no responce.
  14. ImTooOldForThis

    Serial Connection to 11C

    Hello, I have been having some issues connecting to the 11C cabinet via serial. I have my comm software setup to match SSC baud rate, with 8/N/1 config, my issue is: I can see some of the error codes and AUD codes appear in my terminal, but when I press enter numerously to get a logon prompt I...
See more

Part and Inventory Search

Back
Top