Recent content by hinesjrh

I recently took an old HP laptop from our recycling (retired) pile at work, and was going to re-purpose it. Within Windows I took it off the domain and just put it on a workgroup I created. I rebooted but now can't get logged into the laptop, as it doesn't seem to recognize my old (domain)...

Thanks unclerico. NAT is performed at our ASA. Yes, the single 3845 is a known single point of failure. I like your statment 'you can simply add two static default routes and the 3845 will do per-destination load balancing by default'. However, does that only provide load balancing, or...

I have a single Cisco 3845 as my Internet router. Currently I have two 100 Mbps Ethernet circuits from the same ISP, and both of those circuits terminate on the same router at the ISP. We have BGP in place for load balancing and failover. I am changing out one of the two circuits so that I'll...

I have an SSL certificate on my ASA 5520 (running 8.3(2)) code that is expiring soon. My current certificate that was installed a few years ago was created with a key pair bit size of 1024. My certificate authority will only issue certs now with a minimum key pair bit size of 2048. Via the...

I have a Cisco 4510R switch with dual Sup Engine V's (in slots 1 & 2), and currently five WS-X4548-GB-RF45 line cards (in slots 3 thru 7). I'm running 12.2(50)SG for the IOS level. I've purchaed another of the same line card, and I'm wondering what I need to do to add it. I plan to power down...

I have this figured out. I realized that I had a few more steps to go with Cisco. I had to take the 'authorization key' that I received from Cisco after issuing them a PO, and step through their licensing website to get a hexidecimal activation key that is then installed on the ASA. I am all...

I just ordered and received the product authorization key to add VPN for mobile functionality to my ASA 5520, but I am not sure I to install the authorization key. Can someone point me to a document that walks me through the command line or ASDM step to get this installed and implemented? My...

I have a Cisco 3845 router running 12.4(24)T. This router came default with two GigabitEthernet interfaces. I was using one as my LAN connection (inside) and one connects to a 100 Mbps Ethernet circuit from my ISP (outside). I am adding a second 100 Mbps Ethernet circuit for diversity and...

I have a Cisco 2821 running IOS 12.4(20)T3 which acts as our voice gateway. I have three PRI circuits connected to it, along with some POTS circuits. I am attempting to determine how many of the 72 channels (3 x 24) of the PRI's I am using at a maximum. Is there a command to run that will...

Thanks brianims. Do you think the ACL logging uses significant CPU? How can I turn that off?

I am looking to upgrade from my current 3845, which I am pushing the limits on and I don't think a 3945 is a good long term solution. My 3845 is running at 70% - 80% CPU during the day since I have added more bandwidth to it (full DS3 plus 100 Mbps Ethernet w/ BGP) and have a growing ACL. This...

With the help of Cisco TAC, I now have the issue corrected. I thought I would share the fix. It was a combination of me misspelling the IOS name (was missing an s in the advipservicesk9 name) and found that (unlike the way the Cisco upgrade documentation has it) a colon (:) is required in the...

I have the new image (12.4 T5) on the router along with the original IOS image (12.4 7g). I have the boot statement changed to reflect the new image, but it still boots to the old one. What am I doing wrong? Vanguard#show run Building configuration... Current configuration : 10968 bytes ...

What about if I just want to allow ftp?

I currently have the following access lists in place on a remote router (10.27.0.1 255.255.255.0). I need to add the ability to allow ftp from this remote router to a server in my DMZ (10.253.0.0 255.255.0.0) at my host data center location. We've installed a temporary job site camera at the...