Recent content by HelpTheWestie

Hi I have set-up an ACL filter from VLAN1 to VLAN3. This filter drops any traffic going to VLAN3, which i have working. But when i try allowing one host address from VLAN1 to VLAN3 it is still getting blocked.... Can anyone point my in the right direction?? filter act 1 create name "Vlan...

Do you know when Verison 5.0 is due out?? Are Nortel increasing the number of MLT in this Version?? Thanks Help The Westie

Hello, Has anyone set-up an ACL Filter using the New 8630GBR modules?? I'm Running Software Version 4.0.5 I'm trying to block/filter any Ping traffic from my default VLAN1 to my Voice Vlan3.... I'm using device manager and i'm getting very lost!! Any help would be great Help The Westie

Antonyanderberg Thankyou for the above post, I have got port-mirroring mode Many-to-one working using Software 4.3…But, I’m unable to find any release note on this new feature, Arrrrr Nortel doc’s?? Help the Westie

The chassis boot up. When looking at the Show Tech Info i'm not getting any info for the first power supply... So i'm guesting that may be the problem, but why i don't know?

Jonks Are you able to test theses two devices on a Baystack 450 switch?? and all ports running at the same speed/duplex?? Regards

Hi I’m getting the following error msg when booting my Passport (ERS) 8610 seepromGetInfo: crc failed on device 20, calc: efde dev: f0de Hardware: Chassis 8610 1* 8692 SF in Slot 6 1* 8630GBR in Slot 2 Software: 4.0.5.0 Any pointers or help would be great Regards Russell

We are now running software version 3.7.8. For a week i ran an SMLT network with two Passport 8610 with one Switch Fabric installed in both chassic. We have 9 SMLT Switch Stacks 3*450's, 6*5510/5520's. The SMLT network was fine all week. When pinging the interfaces/VRRP addresses of the...

Hi We are not running L2/L3 HA Mode. I have switched the CPU blades and we still get the packet incresses.

In total we have 3 * 450's stacks. We have 5 Vlan's and our VRRP VRID are 15, 16, 17, 18, 19. But why does it only happen when both Second Switch Fabrics are installed?

Hello Please can anyone help with the below problem... We are run 2 Passport 8010 with two Switch Fabric Model 8691SF with 256 MB. We are running an SMLT network with 5510/5520 and 450 Switch stacks. Here is the problem... When both passports are running on one Switch Fabric the network is...

After 2 weeks and alot of playing it is working!! By using the log on the 251 i was able to enter the right Peer ID Values Thanks for your help biv343

You have got the question correct. Here are my setting for the ces 1600 Encryption: - ESP - Triple DES with SHA1 Integrity: Enabled IKE Encryption and Diffie-Hellman Group: Triple DES with Group 2 (1024-bit prime) Vendor ID: Enabled Aggressive Mode ISAKMP Initial Contact Payload: Disabled...

Hi Help.... I have a Contivity 251 and a Contivity 1600. I'm trying to set-up an IPsec tunnel. The Contivity 251 is the initiator, and does not have a static IPaddress. The Contivity 1600 is the responder. How can i set-up the contivity 251 to use a different source address when creating the...

All I have answer my own question rcSysAction.0: nonWritable Is down to running the wrong version of Device Manager... I was running version 5.8.5.0 - Passport 8600 version 3.7.7 need device Manager 5.8.8.0 Ta All