Recent content by Havokmon

Changed from 5ess to national on both the Asterisk and Fujitsu, and it all works fine now.

Looks like the 9600 is releasing the call after the connection is made. I've had the opposite problem transferring out PRI's before.. It wouldn't release the call an allow an outside VM to pick up. I don't know how to tell the 9600 to always supervise the call..

I now have a functional PRI between an Asterisk system, and an F9600. I can call Dt200s at will, and there are no problems. But anytime I call any SIP phone on the Asterisk, doesn't matter how many times it rings, after being connected for about 2 seconds, the Fujitsu appears to disconnect...

Oh! Asterisk is rejecting the call - so it IS going down the trunk! I think I may be good from the Fujitsu side! Thanks!

Yep, I've already done 0-6, or giggles I just opened up 0-60 ASS COS,,304,0,60 Still get "Busy Camp On" on the DT200. It seems the PBX thinks the trunk is busy. Oh duh. It's busy because I didn't SET PTMI after re-doing everything. Now I get Invalid Number. Ugh. And I see nothing in my...

A little further - I deleted my aarlc and re-created it. I seem to have set ID=1. Now that It's 0 (other), I can go out my 'valid' TG PRI in my route 11. I also discovered my TG had the wrong settings. I was comparing with my last test TG, which didn't work either. Setting it to be the...

It's definitely a restriction of some sort, if I put a working outgoing trunk as step 1 in my route 11, I still get restricted. I don't know where else to look.

Nope, but I was able to receive calls from the asterisk over this PRI. For giggles I've done the ptmi now. No difference. I've now totally started over, and followed the above instructions to create my TGs new - after taking it too literally, and setting up national instead of 5ess, I've got...

I've started over with a freshly installed PRI card, and an existing TG that hasn't been used in years. It used to be a local PRI TG, with calls flowing bothways. I've assigned this TG to the new PRI with ISTRK. When I change my ARSR to TG 150 instead of 211, I now get 'Number Restricted'...

Ahh. Ok, that stopped the extra '6' requirement. I think my problem is that this is a PRI, and I don't see where the TG knows how to send OUT the PRI. I see in DIS TRK where straight T1s are associated with a TG, but I don't see where to do that for the PRI.. and ass trk doesn't work for...

Hmm I still get 'Invalid Number'.. I have to dial 66204, the 6 to get into AAR and 6204 to trigger my route, so I assume. But it doesn't seem to want to push the call down the trunk. Any other hints?

Hi guys, I'm trying to create a set of routes to allow anyone who dials 6xxx 'extensions' on the Fujitsu to transfer to an asterisk. I have an asterisk connection via a PRI, and I can call Fujistu extensions from the asterisk, but I can't figure out how to go the other way. My TG is 211, and...

Was cleaning out my inbox and saw this thread. Just posting a follow up that restarting the PBX and voicemail made the change work.

The set relo was off before I moved the phones. I've 'run' this PBX for 6 years - though we don't change much of anything. Turning off Set Relo was one of the first things I did. I had thrown a NIC in the OS/2 box, and am using the Windows Client for VM. Already deleted/recreated VM boxes...

Hi all, I'm running a Norstar PLUS NT7B53. I have two users. One has an 'operator' phone, one has a standard digital phone. So I physically swapped their phones, physically changed the ports in the back. This, obviously, gave them each other's extensions. Then I went in and did a Change...