Recent content by gwilkers

YES!!! KICKASS!!!! Thank you so much gconnect! If you were near me now, I would hug you, kiss you, and take you out for a beer! Whew. I added network 10.32.0.0 0.0.255.255 area 0.0.0.0 and BLAMMO, she's working like a charm. you rock gabe

PLEASE PLEASE PLEASE HELP ME OBI-WAN@!! Here is a print of my sh ip route in case it will help any ric#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external...

Thanks for the help guys, but i'm still having trouble. Here's my newest shru ! version 12.0 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname ric ! enable secret 5 $1$zelC$a2J5E9J.REQOxKUBj1gVI1 enable password richmond ! ! ! ! ! ip...

OOPS, I TAKE THAT BACK! From the local workstation I can ping 10.32.1.1, but CAN NOT ping 10.102.32.1 Gabe

From a local workstation I can ping both sides of the local router. 10.32.1.1 and 10.102.32.1 But I cannot ping either side of the remote router 10.35.1.1 10.102.35.1 Also, I'm not sure if I want this line in there ip route 10.0.0.0 255.0.0.0 10.102.0.0 but i can't delete it. When I perform...

Hello all, I have a 2600 router that crashed this week, and so I swapped in a replacement and am having a hell of a time with the config. The problem is that from the router i can ping the other locations on our network across the frame relay connection. However I cannot ping any external...

Well...forgive my ignorance, but can I get instructions on how to find this out? Thanks again, Gabe

How do I check the retention limits on messages in voice mail, and can I extend this limit? Is their a default? Thanks, Gabe

**bump** Can anyone please help me with how to change the 9 to an 8 to get an outside line? Thanks again, Gabe

I've had some problems with employees accidentally dialing 911 when trying to make outside ld calls. They hit 9 for an outside line and 1 and somehow 1 again, and where we live ANY 911 call is enough to get the police here, and they want to search the building. I want to keep this easy access...

Thanks for the help norstargirl. It turned out, as I and probably you suspected, to be a LEC problem. They finally did thorough enough testing to determine that they could loop from Z->SLIC, and from A->SLIC, but not A->Z. It's fixed now, it never was a problem with the cards, but I...

Thanks to everyone that helped answer my questions in this thread. It turned out, as I and probably most of you suspected, to be a LEC problem. They finally did thorough enough testing to determine that they could loop from Z->SLIC, and from A-SLIC, but not A-Z. It's fixed now, it never was a...

Ok, so the phone company assures me that this is not their problem. All of the NIU (or whatever the T1's come into) show all green status. However... The Meridian still shows a 'red alm' light. This light stays on even after I do a 'disc 2' and 'disc 3'. I pulled the card, and slipped it...

Can anyone tell me what the top error light means when lit orange on this Norstar Digital Card? I have a T1 that goes between this system and a Meridian with a line side t1 card in it. There is also an error on the Meridian system card. The T1 going between the two has been checked by the...

Those commands appeared to work and do what they were supposed to do. However, the status of the 'red alm' light never changed. Is there anyway to power down only that card? Or to make it safe to remove and reseat with shutting down the entire system? I'm kind of at a loss of where to head...