Recent content by grotongroup

Hi; We're trying to utilize a ScanFob bluetooth barcode scanner with an Acer-A1(810) tablet/Android 4.2.2. It will pair, but we can not get the keyboard to activate with the scanner. Does anyone have experience with this or offer suggestions. Trying to roll-out a mobileApp inventory solution...

We have hundreds of Symbol PDT6846 barcode guns and find that they can assign either a window of 1440 or 2880 at boot-up time. 1440 causes significant slowdowns, 2880 is much better. How can this be assigned to have a window of 2880 consistantly. Thanks GrotonGroup :)

Hi, Thanks for the response. We have prioritized our QOS on the MPLS and for the most part, that is under control. The wireless bar code guns appear to be the major issue with latency and one of our senior network IT specialists discovered the Nagle's alogrythm issue. It makes sense with how...

We are investigating packet latency RE: Nagles algorythm. Running HP-UX 11.31, over 50 remote locations via MPLS and supporting RF barcode applications in these sites. Latency has been an issue especially with the barcode guns. Running telnet (port 23) for the guns. Hoping someone can share...

I'm trying to change the font in a document. I have tried changing the symbol set first Ec(10U then changing the typeface Ec(s16602T but I appear to be getting only the defaults. I'd like to print Arial or Lineprinter. Thanks, GrotonGroup

Gentlemen; The information in this last post was excellent. I have been able to take the examples and info, make the modifications and add the logic needed to fullfil the project requirements. Thank you, GrotonGroup

Thanks again, much info to absorb :) Grotongroup

Thank you both !! I will try this code... Grotongroup

Gentlemen; Thank you. I'm an old time coder and have most of the HP Laserjet font,orientation,style functionality under control. The graphics have been more than challenging. This project runs on an HP-UX box using a former IBM PostRelational Database (UniVerse). The programming language is...

Jim; This is the captured output file: I have not set margins, length or spacing. Just using the defaults. E &l1O Landscape Mode &l5.45C *p0x370Y *c750a300b0P *p+1075X *c750a300b0P *p+950X *c750a300b0P *p5x375Y *c745a290b1P *p+1080X *c740a290b1P *p+950X *c740a290b1P *p0x2750Y...

Desired Result -------------------- ------------------ ---------------- | | | | | | | | | | | | | | | | | | --------------------...

Output as requested: I have the three boxes printing. 0001: ^027E 0002: ^027&l1O 0003: Landscape Mode 0004: ^027&l5.45C 0005: ^027*p0x370Y 0006: ^027*c750a300b0P^027*p+1075X^027*c750a300b0P^027*p+950X^027*c750a300b0P 0007: ^027*p5x375Y 0008...

Jim; I'd like to draw three(3) vertical lines below the boxes that you indicated. They will be printed in landscape mode at coordinates 0,2750 / 0,2125 / 0,275 I appear to be getting a top-of-form and change back to portrait. Suggestions. Here's the latest code: 0010: printer on 0011...

Jim; Thank you... Definite progress is being made. I'll be tweaking it now. Thanks for your assistance. GrotonGroup

Thanks for the info, but my end of line = char(10). Currently, the boxes print the correct sizes but the run down the left vertical side, not three(3) across on the horizontal plane. My first one starts at 0,350 then next box should be to the right of the first one and then the last box to...