Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by groej

  1. groej

    IX Workplace Andriod WLAN

    Hello everyone, we have an IPO SE Select with SBCE and R11.0 FP4 SP3 in operation. I have a strange behavior with the IX Workplace on my Samsung Andriod cell phone. Everything works in the company via WLAN. Presence, phone book, call forwarding and of course telephony. If the cell phone goes...
  2. groej

    unkown IP adress in SCN Network Status

    Hi, the IPO500v2 are in other locations. There are no port diversions on the IPO's. If I disable this IP address in the firewall, the IP remains visible under SCN Network Status. The IPO's are only accessible via the VPN site networking. If one looks in the monitor under TCP stream one does...
  3. groej

    unkown IP adress in SCN Network Status

    Hi, I always find in IPO Server Edition systems in SCN Network Status IP address that neither fit to the system or are not programmed in the system. Funny is that it is always the same IP address and if only with the IPO500v2 devices is to be found. These can not be found in the primary or...
  4. groej

    ASBCE with J179 phone remote worker

    Hello, i have find this in the monitor log: IsReceivedKeyMatchWithKLineInOfferSdp::K-line key match result - 2 K-line mismatch is detected and forcefully disabled the media security
  5. groej

    ASBCE with J179 phone remote worker

    Hello, I apologize for my bad english. I have a problem with the ASBCE and J179 phones as a remote worker. OneX Mobile and Equinox via ASBCE also work with VOIP mode (TLS and SRTP). The J179 phone fetches the config file and the extension and the user logs on to the IPO via the ASBCE...
  6. groej

    Equinox for IP office 11

    Hello, I had the same problem. You must enter a Realy Agent under DMZ for HTTP with port 443 to the IP address of the IPO.
  7. groej

    outgoing caller ID not showing the number on IPO over BRI Trunk

    If 0 is the access code for the bri line then Code:0N Number: NSi40238873 Line ID: Group ID from BRI when you want to send not your own number the provider must support clip no screening.
  8. groej

    one-x service not runnung after reconnect dsl trunk

    Hello to all, thanks for your answers. Why should I ports or passwords check if everything goes after a restart of the one-x portal service on the app server? Only the CSTA provider does not work after a reconnect from the VPN tunnel. Why the CSTA Provider not reconnected after a line break to...
  9. groej

    one-x service not runnung after reconnect dsl trunk

    Only the CSTA provider is not connected. DSML is ok after the vpn tunnel is reconnected. Why does the CSTA provider not reconnect from allone like the DSML provider? After restart the onex service on the app server it runs.
  10. groej

    one-x service not runnung after reconnect dsl trunk

    no they are not in the same location. it is an scn with two ipos und one application server. one ipo is not in the same location an this ipo is the problem at one-x portal.
  11. groej

    one-x service not runnung after reconnect dsl trunk

    no they are not in the same location. it is an SCN with two ipos. but why try the service does not establish the connection again?
  12. groej

    one-x service not runnung after reconnect dsl trunk

    hello, my one- X Portal service provides no connection when the DSL line has been disconnected and is being rebuilt. On the dsl line a vpn tunnel is established. Only when I use the one- X Portal service reboot the connection to the ipo is restored. One-X portal is installed on an application...
  13. groej

    R9.1 SP4 Softconsole hunt group logon - logoff for User

    Hello, i have a problem with the softconsole. You can logon and logoff other user over softconsole to huntgroups. But the field with the huntgroups is empty. I can´t select a huntgroup for logon or logoff. I use R9.1 SP4 for softconsole and ipo. Have anyone a idea? greetings Joerg
See more

Part and Inventory Search

Back
Top