Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TouchToneTommy on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by gmiller1949

  1. gmiller1949

    NICS forward calls to voicemail.

    Try feature 984
  2. gmiller1949

    can't access Call Pilot over the ethernet

    Guys, I had the customer reboot the system and all is well. Thank you all for your time and experience. gmiller1949
  3. gmiller1949

    can't access Call Pilot over the ethernet

    Allworxguy....tried Firefox with no success. Curlycord....when I get to the password prompt, I'm connected. When it fails, I don't get to the prompt, it just stalls. Sorry if I was not clear. Anyway, I'm going to have my customer reboot on Friday after COB. Stay tuned, I'll post my results...
  4. gmiller1949

    Can't access Call Pilot 150 over the ethernet

    I asked the customer, but timing is not right. The system is functioning properly except for remote access. Will reboot after COB this Friday. Stand by for my update. Thank you.
  5. gmiller1949

    can't access Call Pilot over the ethernet

    I'm using Windows Internet Explorer ver 9.0.23 I enter the IP address of the CP150 in the subject line and it takes me right to the password prompt using AT&T MPLS cloud network. I have 32 systems across the country, so direct connect is not available. All systems work with exception of about...
  6. gmiller1949

    can't access Call Pilot over the ethernet

    We have several 0x32 Nortel units w/Call Pilot 150. Typically, I enter the IP address (of the CallPilot)in my browser subject line and connect. Recently, I cannot connect. The Call Pilots are functioning, answers to "PING", all LED's are lit and I can access via the RAD using feature 983. I just...
  7. gmiller1949

    Can't access Call Pilot 150 over the ethernet

    We have several 0x32 Nortel units w/Call Pilot 150. Typically, I enter the IP address (of the CallPilot)in my browser subject line and connect. Recently, I cannot connect. The Call Pilots are functioning, answers to "PING", all LED's are lit and I can access via the RAD using feature 983. I...
  8. gmiller1949

    rack mount an MICS

    yes, that's what we are doing now. Big boss wants a LAB with everything mounted in racks and was asking about the MICS.
  9. gmiller1949

    rack mount an MICS

    IH17, thanks for the response....that's sort of what I thought.
  10. gmiller1949

    rack mount an MICS

    does anyone know if Nortel makes a bracket to mount an MICS in a relay rack such as Chatsworth 19" ?
  11. gmiller1949

    PRI enabler key code

    Yes, the old 1A2 is a system by itself, as is the Norstar. You tie the T/R from the 1A2 to the CO of the Norstar and connect the A1 leads of the lines and the two systems work very well together.
  12. gmiller1949

    PRI enabler key code

    Sure does. using Norstar 1A2 trunk cartridge. Tie the A1 leads together and you even get light supv on both systems.
  13. gmiller1949

    PRI enabler key code

    yes, it is a very old system. Even has 1A2 key equipment attached (Verizon C.O.). This is a trouble not a new install. We may ditch everything and move on to a BCM.
  14. gmiller1949

    PRI enabler key code

    I have 0x32 w/ XC1.1 I need to enter the PRI enabler code, but "HARDWARE" does not appear in configuration.
  15. gmiller1949

    wrong DN from the 6-port exp card

    Dasheen, yes, that is what I do....I was hoping for a fix to have the DN's appear as they should. Thanks gm
See more

Part and Inventory Search

Back
Top