Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by GLHEC

  1. GLHEC

    SCCP, SIP and H.323

    howdy. i have a general question concerning call setup and call handling. i am in search of how a call actually works through the 3 control protocols. im pretty sure h.323 handles call setup AND all voice traffic as well. as opposed to sip where setup may be handled by one and the actual...
  2. GLHEC

    QOS Best Practices?

    thanks for the help!
  3. GLHEC

    QOS Best Practices?

    Thanks for the info. I see control is COS3 and media is COS5. I was working on a 3550 that has 4 queues, with one of them for priority. Having only 1 queue for priority, I think I can only match one COS label to it. This is a problem if I saturate a layer2 trunk upstream (since only media is...
  4. GLHEC

    QOS Best Practices?

    Is there a best practice for mapping dscp or cos to voip control and voip media traffic? I am looking for a doc that says voice control in most cases should receive dscp X and cos of X. The same for voip control. I understand that it could vary on each network but there must be a general...
    • GLHEC
    • Thread
    • Replies: 4
    • Forum: Cisco
  5. GLHEC

    FXO& route pattern= busy signal

    i have the fxo port configured with a DN of a voip phone for inbound calls(future i plan to have autoattendant) and i have a route plan for the fxo port, 9.@
  6. GLHEC

    how to configure/use fxo with callmanager

    i found some doc and have it somewhat configured but am haing issues. there is another post regarding fxo and fast busy. thanks for your help
  7. GLHEC

    FXO& route pattern= busy signal

    this is a ccm install.
  8. GLHEC

    FXO& route pattern= busy signal

    when i configure a route pattern to exit my fxo card, it works. but when i attempt to dial digits following the connection i get a "phone has been off the cradle too long". so i have a route pattern for the number 9. i pick up a phone, enter 9, then i get dialtone. after i attemt to dial...
  9. GLHEC

    Need Help configuring CCM 3.3

    i would start with the cisco callmanager administration guide. google it. also i hear cisco press has some good into.
  10. GLHEC

    command to get serial numbers?

    ideally i would like something for all cisco devices, but mainly for a cat 6500. thanks
  11. GLHEC

    command to get serial numbers?

    is there a command or mib oid to get a switch chassis serial number and card serial numbers? any ideas or scripts or anything would be great. thanks
    • GLHEC
    • Thread
    • Replies: 3
    • Forum: Cisco
  12. GLHEC

    how to configure/use fxo with callmanager

    i have callmanager and a gateway with a fxo card. what do i all need to do to get it to work? i cant seem to find any doc on configuring it, or at least anything i understand. i would like it so my voip phones can call out on it, or have people call in on the pots line. thanks
  13. GLHEC

    Conference with pots phones

    EDIT ABOVE POST- the pots phones are configured with ccm. they are hanging off of a 3725 which is using ccm as well.
  14. GLHEC

    Conference with pots phones

    Can i conference with pots phones off of a 3725? is there any doc? thanks
  15. GLHEC

    CCM and Gateway config

    I got it working. I had a prefix DN entered which broke things. thanks everyone
See more

Part and Inventory Search

Back
Top