Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by GlennComiskey

  1. GlennComiskey

    Remove fileset update

    p5wizard, Thanks for the info, and enlightenment, much appreciated.
  2. GlennComiskey

    Remove fileset update

    DukeSSD, Thanks for the post. Unfortunately I have no prior experience of AIX, having previously work exclusively on Solaris, and do not as yet understand the concept or implication of committed or non-committed filesets. Hence why when I read the man page it doesn't make any sense to me at...
  3. GlennComiskey

    Remove fileset update

    As a newbie to AIX, I'm proberly asking a very basic question but please bare with me. I have just updated the Java runtime on a server from 6.0.0.1 to 6.0.0.175, which is comfirmed by lslpp -l as being COMMITTED, to correct a fault with an application. I would, however, like to rollback the...
  4. GlennComiskey

    IP address secondary feature

    Firstly, apologieses to all who posted for delay in responding but have had difficulty finding time to follow up postings - especially as Easter Bank Holiday weekend (UK) got in the way. Can confirm that trunking not possible with 2503 (your were right ibknelson), which is what I was first...
  5. GlennComiskey

    IP address secondary feature

    Hi, If I assign a secondary IP address from a different network to an ethernet interface, does the router perform routing between the two networks? I.E. - ip address 192.168.1.254 255.255.255.0 ip address 192.168.2.254 255.255.255.0 secondary C2503>show ip route Codes: C - connected, S -...
  6. GlennComiskey

    Cisco 2620 not receiving routing updates

    Burt, Thanks for the posting, much appreciated. Can't see that I am doing anything wrong, and C2503 still doesn't reponding to ping either as sender or reciever, so it does look like the router is faulty. C'est la vie. Glenn
  7. GlennComiskey

    What cable I need to connect 2600 to 2500 router?

    Burt, Thanks for the posting, much appreciated. Can't see that I am doing anything wrong, and C2503 still doesn't reponding to ping either as sender or reciever, so it does look like the router is faulty. C'est la vie. Glenn
  8. GlennComiskey

    Cisco 2620 not receiving routing updates

    Burt, please see other thread.
  9. GlennComiskey

    What cable I need to connect 2600 to 2500 router?

    Burt, Did take down serial interface on C2503 and as suspected it made no difference, either pinging from or to the device. Therefore believe this just confirms that there is a physical fault with the router. BTWYAFA. ------------------------------------------------------------ C2503#show ip...
  10. GlennComiskey

    Cisco 2620 not receiving routing updates

    Burt, Both serial interfaces on C2503 were assigned to subnet 192.168.254.0/24 simply to make it easy to use/move the single DCE/DTE cable I have between the two interfaces. In previous configurations where only one serial interface has been used, it has made no difference. Don't believe there...
  11. GlennComiskey

    Cisco 2620 not receiving routing updates

    Discussions via another thread have lead me to believe the problem is that the serial interface transmitters on router C2503 are not functioning properly. ------------------------------------------------------------ C2620#show run Building configuration... Current configuration: ! version 12.0...
  12. GlennComiskey

    What cable I need to connect 2600 to 2500 router?

    jneiberger, Have reset routers and created basic setup. As you'll see from details below not able to ping to/from the C2503 router. Tried with both serial interfaces on C2503. Same response/output when using C2611 rather than C2620. When using C2611/C2620 (details not shown below) I am able to...
  13. GlennComiskey

    What cable I need to connect 2600 to 2500 router?

    jneiberger, Do not suspect serial interfaces on C2611/C2620 as when connected together both report in-bound/out-bound traffic, i.e. both transmitters/receivers working. This is supported by the fact the C2503 will receive routing updates from either router, i.e. their transmitters working. This...
  14. GlennComiskey

    What cable I need to connect 2600 to 2500 router?

    Burt, have checked interface stats and can confirm that when connecting C2611/C2620 both report sending/receiving packets. However, when using C2503 and C2611/C2620 only the C2503 reports receiving. Would indicate cable fault, except cable works fine for C2611/C2620. Presume there is a...
  15. GlennComiskey

    What cable I need to connect 2600 to 2500 router?

    jneiberger, details as requested. C2611#show run int serial 0/0 Building configuration... Current configuration: ! interface Serial0/0 ip address 192.168.254.2 255.255.255.0 no ip directed-broadcast no ip split-horizon no keepalive clockrate 2000000 lan-name SER0 C2611#show int serial...
See more

Part and Inventory Search

Back
Top