Recent content by Gallian

A problem with LSU yes can be but does anyone agree that the LIMs are trying to restart but cant restart due to the disturbance counters set to 0. I dont have remote LIMs the group switch connections are good but due to some reason the LIMs are trying to restart but cant. One of the reasons...

Hi rfpui, I think The license is for the analogue extensions not for CLI feature.Every analogue extension will be able to get CLI if u have the ICAT set so there shouldnt be a license issue tagged to CLI. BR Gallian

Hi, I am getting this message very often "Message from the operating system Restart requested LIM initiated" and soon after that I get another request for relaod. Although I am not getting any restarts but soon after I get an alarm stating LIM out of order and relaod failed in lim. Could any one...

Hi, If it is NIU2 u may need to upgrade the Firmware to R6A. Else resetting the NIU should solve ur problem but do wait till the alarms for device boards faulty or missing is receive then put the board back and wait again for device board activated. After that u should be able to log on. BR Gallian

Hi, In BC 11 there was an OMR developed for analogue CLI and it works fine with a patch and a PROM change on the ELU 29 boards. It is defrinitely possible in BC 11.All u need is the patch and the PROM for ur analogue boards. BR Gallian

Hi FCPLI and soaplover, Does ur replies mean MD110 BC 9 can not have CLI for analogue extensions, as far as FCPLI's FAQ I think its possible can we get some further help on that please. In BC 11 does it have to be thru an OMR doesnt the China version has CLI functionality. My customer wants...

Hi, I think a TLU76 can also be used in this scenario but we have to use a TLU 79,EDSS1 protocol. A simislar config does also exist some where in EGHAM Surrey UK. Its also using a TLU79. BR Gallian

Hello Guys, My customer wants to have the efax functionality for there office using TLU79. They want to use Virtual Etensions for this purpose can somebody explain how will it work I have the route parameters but what I dont understand is why do we need to have virtual extensions for this...

Hi, I agree with Vitenari try sending +++ and wait for few seconds u should hear the disconnection and then send ATH0. After ATH0 If ur modem speaker is off u wont hear the disconnection noise. Gallian

Hi, U can look in the SEL parameter of the Route Data the D3 might be what u looking for. You can change it in ROCAC. BR Gallian

Hi, Another way is to check the ELU 29 board, some of the /11 boards do have this problem try replacing the board whos individual does not get the ring. Some times due to external voltages the ELU 29 is unable to get rings. SO try and find out if the ring is not received on one individual or all...

Hi, I have also faced this problem a lots of times and sometimes it was days I was unable to take a system dump just because of this error.Even though I used to dump the system at a very low traffic times. Even restarts of the failed PU wouldnt help. I had to reconfigure the whole GSM cables and...

Hi Bartjo, Well If u have configured form=5 then that means u have a self defined the out put format. U can take CLFOP:FORM=5; and see whats the format like. Offcourse when u will change the FORM =2 that will effect the TABS. So the best thing is to check the CLFOP and see the DATA. BR Gallian

Hi Patcher, The site that has this problem is bit far I am planning a site visit and will used ur SACOS. I do not have modem access to the site. Will get back to you soon. BR Gallian

Ok, We do have a voice mail system and the Incoming calls are routed to the auto attendant,thats DIAVOX everything is then handled and routed by the voice mail system.The DISA has not been initiated. The Problem occurs only with outgoing calls. The alarm 260 is present in the ALLOP when this...