Recent content by FrankGrimes

Hi Billz66 They are fixed user but all user have micollad licencing and are created through micollab, so they have access to soft, UCA and desk phones. The problem i was testing was desk phone to two outside lines. The trunks are ISDN. Yes the new integrated fancy handsets. All to outside...

Hi guys we have a Mitel 3300MXE II running software version 8.0 v2. We also have a whole bunch of 6940 ip phones. None of these phone will conference in user with the join button. So user A picks ups the phone and dial user B. User A hits Add user then dials another number. Once they hit the...

I setup a small test group and users with the new firmware, and they actually use DHCP so I point the TFTP at the vMCD. It worked for three months. More then 200 handset have already gone across, no complaints.

I moved the 5324 (also the 5312) firmware files from a vMCD and imported them into the MXE. The upgrades are happening as the handsets are rebooted, so one at a time. In a weeks time I'll do the big bang but this should at least keep the load down and the outage to a smaller block of users. I...

Bobcheese. With G729 you only require about 25kb per call, but QOS is setup on UDP tagged traffic so the upgrade will go in with everything else. As for slow I'm talking about 512kbps sites. So 600+ phone over 400+ sites, the MXE is only able to upgrade a few phones at a time therefore the last...

I have to upgrade a MXE to version MCD 6.0 from version 5.2. I have 600+ phones broken up into 3 handsets each on very slow sites. So the firmware upgrades are going to take at least 8 hours. I wanted to speed up the handset firmware upgrades but moving the firmware from a version 6 unit into...

I have a Mitel sip trunking into a cisco call manager. The cisco is UC500 and in our sister office. Trunks work fine, calls between site sound great, I have no IP issues, nor firewall. The call scenario is like this: Cisco ----> Mitel vMBG----> Mitel vMCD----> Reception answer then transfer the...

I didn't know that vmcd could do embedded, the Mitel supplier we buy from didn't even offer it. To be honest the client doesn't want vmail at this stage, but the system I'm installing will be a fly in fly out job in a country that I would prefer to support remotely, which is why I'd rather...

Hi, I have one Mitel vmcd and one Mitel 3300 cxi. I would like to use the CXI embedded voice mail for the vmcd. I'm trunking via xnet and can make calls between the two sites. I can't call re-route calls on the vmcd to the cxi pilot because its not a really directory number. I have tried a hunt...

If you PM me your email address I'll flick you over some screen shots.

I think either way im stuffed. I feel more comfortable with the Asterisk but that might be because that's what I know. Slapin solution sounds very interesting but I'm not a programmer :(

Yeah the carrier can provide this type of data BUT I have been asked to route calls via an MPLS network out to specific country to other phone systems which means I wont be able to collect that data without some kind of billing system attached. I would love to use something like CAAB or CVT...

Hi All, I have been asked to connect our Mitel 3300 MXE to a PortaOne billing system. Link From what I understand PortaOne connects to Cisco and Quintium phone systems using radius authentication. It also captures calls stats using the same method which is why I've been asked to connect to it...

Yes I have an expansion pack. I just used that tool and it said its only going to use 56% capacity. What software do you guys use to monitor your Mitel? I've used one SNMP piece of software but it only give basic data link, trunks up, user online. I wouldn't mind something that has CPU load...

I have a Mitel MXE 3300 with 450 users two 30 channel ISDN service 30 sip trunks to 4 different phone system, and will be installing another 100 handset next week and 12 more sip channels on another from another carrier? I know the specs for my system are 1400 users but I still worried that one...