Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Recent content by Fatty99
-
Is my 2620 alright? weird boot
Never seen this error message before but I have looked it up at the cisco site: According to the error message decoder at the cisco website: %IP_SNMP-3-SOCKET: can't open UDP socket The SNMP server was unable to open a port for receiving or transmitting SNMP requests. This error usually... -
Cannot Ping
ip route 10.120.0.0 255.255.255.0 10.2.2.1 ip route 10.120.1.0 255.255.255.0 10.10.10.235 --> NOK ip route 10.130.0.0 255.255.255.0 10.2.2.1 ip route 192.168.168.0 255.255.255.0 10.2.2.1 Reading your post, I assume 10.10.10.0/24 is your local network and 10.120.1.0/24 is your remote network... -
Embedded jpg links do not load
ljz1, This is probably a problem with MTU size. This could be client-side, server side or on 1 of the routers on the path. U could try a couple of things. 1. lower mtu size on client side 2. enable path mtu discovery on client 3. increase mtu size on your router. If the problem is caused on... -
Cisco 1701 on BT
Hi brand1068, Personally, I never worked with cisco sdm, I suggest you just use CLI connecting by console. Just connect a pc from com port to console port on the cisco and use f.e. hyper terminal. Just copy paste commands below in terminal. en config t ! interface Dialer0 ip unnumbered... -
Cisco 1701 on BT
Your config isnt correctly setup. 1. You are using a private subnet 10.10.10.0/24 on your LAN interface FastEthernet0. Doing so, u need the router configure with NAT. f.e add the follwing commands. ! Interface Dialer0 ip nat outside ! and ! ip nat inside source list 1 interface Dialer0... -
How to block DHCP requests on interface?
here is what i am thinking ip access-list extended Deny_DHCP deny udp any any eq bootpc deny udp any any eq bootps interface FastEthernet1/0/23 ip access-group Deny_DHCP in I have put this is, but before I plug cable in, anyone see anything wrong with it? This won't work. It will deny all... -
interface tracking
Just out of curiosity, why do u want to use the loopback interface for your external address? Cant u use the dialer interface and nat between the dialer and local interface/subnet ? grtz, Fatty -
Routing Trouble
Are you sure the subnet (192.168.3.0 255.255.255.0) of the remote site is known on the old router ?? and routed to your new core router ?? Can u post ip route of the old core router ?? grtz, Fatty -
Cannot see VoIP packets under SERVICE-POLICY OUTPUT
Try using "show policy-map interface fastethernet 0/1" If this still doesnt show matches on platinum traffic. See if u have matches on your ACL 102 by using "show ip access-list" If u dont have any matches their, then you traffic indeed is not tagged with correct DSCP values. U could check... -
Access Internet from Cisco 2621
Main router config: int fa0/0 ip address 10.1.1.254 255.255.255.0 int s0/0 ip address 1.1.1.1 255.255.255.252 ip route 0.0.0.0 0.0.0.0 10.1.1.1 ip route 10.3.1.0 255.255.255.0 s0/0 Remote router config: int fa0/0 ip address 10.3.1.254 255.255.255.0 int s0/0 ip address 1.1.1.2... -
Debugging to see traffic?
oops --> correction it is --> ip accounting output-packets -
Debugging to see traffic?
I see you resolved your problem. Just to add something, if u just wanna know source/destination ip adresses, u could also use ip accounting. for example config t int fa0/0 ip accouting outpackets. show ip accounting This will show source + destination ip adresses of outgoing packets on fa0/0... -
How to configure redundancy t-1
U can set bgp local pref >100 for ur primary link neighbour. f.e. ! neighbor ip-primary-isp bgp local preference 200 . ! Or use a route-map to set local pref for incoming updates. ! neighbor ip-primary-isp route-map SET-LOCAL-PREF in ! ! route-map SET-LOCAL-PREF permit 10 set local-preference...
