Recent content by farmerfred

the AFRS is built for Rt 31, and is the only AFRS in both switches so that means for a given dialed number, the opr is the same weather the phone is toll restricted or not. From what I can tell from my NEC school books, the programming manual, and my class notes from many many years ago, it...

We have 2 IPXs CCISed together. Toll restriction works fine at the main site (site with the various outbound routes). I cannot make an RSC work at the remote site that is toll restricted baised on number dialed.. and I'm going C R A Z Y !! I built ARSC for RSC 2 = 2, RRI 3 = 2, ATDP Day RT...

This may sound hokie but it works!!! We use one cd player with a non ASCAP or BMI cd and feed the audio to all three of our switch sites over our T-1 network.... we have a (and I'm not braggin') Radio Shack mini speaker amplifier with a wall (wort to power it)at each location feeding music on...

AH HA!!!! It is/was AMND in the closest (actually both) 2400s.... the tables were built as 94 with 12 digits!!! nice short-cut in the original 2400 programming #*#*??#*!!! Program it correctly and guess what.... it works fine!!! I knew I was suspicious when the installation tech put the new...

The 2400 is ok because I use the same Rt.s for all other outside calls, and 911 and they all work... Fred.

Yes, we are doing the routing and 1900 etc. restriction and the true LCR (routing 1st to our own fx trunks) in the "main" 2400. I see, so "already assigned" is the same as "digit request exist" on the 2400!!??!! ok, in 8A4005 14 is a 0001 and in 8A4005 141 is "WRONG-" as is 1411 I but they...

Doug... another hint (perhaps) there is a fairly long pause after dialing the last "1" (9411) before you get reorder tone, so I looked at number of digits CM 855 it looks fine. I looked at the T-1, and it never siezes a trunk when 9411 is dialled. List up of CM 8a4005 is: 0 ALREADY ASSIGNED...

Help, I don't deal with our 2000IPS very often (it's no 2400!!) the users just discovered (after 10 months) that they can't dial 411 (9 411) fortunatly 9 911 and 911 work!! I'll be darned if I can find anything in CM 8A4005 or 8A4007...and to me the LCR in the Feature Programming manual is...

The IPS is 3rd in line after 2 IPX's all ccis'ed together via our own T-1 network (fiber and microwave)all trunks (out & in) term at the main IPX, calls for the IPS route through the second IPX then to the IPS. The IPS DT is louder than outbound RBT and called party, also DT is louder than...

NEAX, Thanks for the help!!! Fred.

Can or does the IPS do the user changeable feature: feature key + 2 or feature key + 4 on a D Term for receive level hi/low and transmission level hi/low like a D Term on a 2400 IPX???? I cannot find the answer in any NEC documentation (features and spec. nor programming manual)(not too...

try www.carlsonwireless.com or http://www.carlsonwireless.com/T-PE.htm we have one and it seeems to work just fine for a hello phone and a modem line

We just bought a two line 2.4 GHz spread spred spectrum point to point made by ??? I'll find out who made it wednesday morning if you like... it was a company in Nothern California...... they have a fairly extensive web site.

there are digital phones (D Term) and analog phones, they use different cards. I don't remember the card numbers off hand, I'll check when I get to work and post again. How many "chassis" do you have? I have some .PDF files on the neax 2000 at work I could send you... Let me know. I...

I have a bunch of 'em as a do all tech with a water and power utillity, (component level trouble shooting to pouring concrete, well almost) phones are my favorite part of the job, probably because it's only 2 to 5 percent of the job, and I keep the swithrooms at 65 degrees....there are lots of...