Recent content by falwiz

Can someone explain how this is setup. I have a site with an Option 61 and I need to setup a new route that dups the existing Verizon PSTN route for a Bright House route. I have all the setting correct and copied the other route to a T but for some reason the default tree that is used on the new...

Thank you for the replies that is kind of what i was thinking. I will head down another path.

To all, I'm setting up a duplicate setup in an option 81 to replace the Verizon T1s coming into the PBX. I have a new set of circuits and have built new loops, d-channels, trunks, and routes. the problem is that the default setup is showing me that the NDNO is the default used which will not...

Never mind I found the errors in my way. Wasn't paying attention to what kind of Network Module i put in. NM-W2 needed a NM-V2.

Can anyone tell me if you can get a 2 or 4 port FXO card to work in a 2651XM router? If so what do i need to get it to see it in the configuration. I thought it was a network module issue but at this time i cannot see it. Any help is most welcome. Novice user so please be kind.

To add to my last message, I beleve if you remove your RLS to nothing you should get your pass through.

I have another issue here but my message waiting is working well from Call Pilot so here is my DCH config. I have 12 sites with no less than 4 DCH configuured this way woth no problem. ADAN DCH 72 CTYP MSDL GRP 0 DNUM 12 PORT 2 DES QSIG_MGCP_CISCO0 USR PRI DCHL 72 OTBF 32...

Yes my RCAPS are a like and here is what i have. ADAN DCH 72 CTYP MSDL GRP 0 DNUM 12 PORT 2 DES QSIG_MGCP_CISCO0 USR PRI DCHL 72 OTBF 32 PARM RS422 DTE DRAT 64KC CLOK EXT IFC ISGF PINX_CUST 0 ISDN_MCNT 300 CLID OPT0 CO_TYPE STD SIDE NET CNEG 1...

Sorry for that here is the error. PRI5033 72 4 "An application has requested to send on a QSIG a non-call related message received on MCDN but the QSIG RCAP is not configured on the outgoing link or the service is not supported on QSIG. The message is rejected. Output: DCH or DSL number...

Can someone help me find a way to track down a PRI5033 error? I've been trying to track them via DCHL messaging with no luck. The route in question for these 6 T1 are used to connect our Option 81 to a Cisco Call Manager. If you need more info I can add to this but I just wanted to start...

I'm tring to login into our voice services card on our option 61 for upgrade/change request and someone has ran off with our book on the login process. we have everythng needed to get in except the default login info. can anyone help? the card is a NTHF77AA. thanx

Yes now i have gotten 2 phones to work last week and now they don't find the call manager on the final step the register the connection, get an IP address but i feel that im losing it on the TFTP part. Any of the phones i have done are Dups of working phone in the system.

I recently was put in charge of our call manager 3.3 and i cannot get any of our new replacements 7920 phones to connect. The ones already connected to the system work fine(turn off and on) but the new ones just stay in a state "connecting to CallManager 0 or 5". Now the sets that are working...

I got it thanx for the replies someone has messed with the RLIs under SPN 0. I got it working right now :)

We presently are having an issue with people using an outside operator to make personal long distance and international calls. The problem is we need to keep access to dial international calls. Is there a way to route to an internal operator on dial 0 and not mess with international calling? Be...