Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by Engleberth

  1. Engleberth

    Do we have a choice?

    "(any one cares about Sinix?)" Me too ... I have a need to become familier with it - any suggestions or pointers ?
  2. Engleberth

    Phaser 780 Lower Heater Lamp

    The fusers from the different rebadged Fuji-Xerox 'Renoir' Engine all used compatable fusers (just a different combination of cutout plastic lugs underneath to make the appear 'specific'). We did not encounter the option to buy the lamps seperatly although if the lamp has failed good chance is...
  3. Engleberth

    Paper error Phaser 350

    Check the RHS of the tray - you will find some cutouts in the side at the front. Wear & tear tends to cause the correct 'fills' to pop out thus confusing the machine. open closed open is the sequence for A4 paper open closed closed is the sequence for A4 Transparancys There is also a...
  4. Engleberth

    Phaser 850 Init then Warm between every page

    Sounds like you may be loosing temp out of the p/head possibly caused by a misalignment. There should be no need to adjust the 850 (only the 840) do you know if this has ever been done?
  5. Engleberth

    Printing labels with phaser

    There should not be a problem doing this. Just remember the poorer the quality of label the more likely they are to peel off or execss glue squidge out & start to gum the machine up.
  6. Engleberth

    phaser 850 error - 05,001.41. Please help.

    Be very careful with this sensor as it seems to be very prone to static damage when handled. At the very least ensure you are at the same static level as the machine chassie although do not leave the powerlead plugged into the machine as the mains switch does not fully isolate the unit and a...
  7. Engleberth

    Phaser 350

    Where are you located? US, UK, Europe, etc ?
  8. Engleberth

    I have useed flowing code to open

    What errors are being generated? I had a simmiler problem using an SMTP library - the problem was I needed to add the relevent dll onto the client machine
  9. Engleberth

    Auto Form Refresh

    OK my mistake - I'm sure the system slowed down when I used the sleep command as at the time I couldn't see any difference between using that & creating a predefined duration null loop. Must have been something else influencing :) I've had a look & it seems a good thread on timer use was...
  10. Engleberth

    Auto Form Refresh

    I am after a method whereby a given form automatically refreshes the data displayed on it after approx 5min. I've looked into using sleep etc. but this method is rather too resource heavy. Is there any other way this can be done considering that the form may not have any other activity occur on...
  11. Engleberth

    Phaser 350 serial troubleshooting cable

    It's not just a straight pin-out chips are involved @ the PC plug end
  12. Engleberth

    Printer cleaning

    Don't lube plastic bearings or the shafts as they are self lubricating (unless worn out). The matrix head can be cleaned with IPA (or whatever subsitute RS components are selling these days). Be careful of some of the sprays as when sprayed on plastic casing can cause surface melting &...
  13. Engleberth

    Color Laser Recommendations

    Give more weight to a personal recomendation that to a review. The QMS Magicolor 330 got raving reviews & voted the MAC best printer awards .... who voted you ask cos it was not the users or the bulk of them anyway. The review came out before many machines had hit the field and 95% of people...
  14. Engleberth

    Firmware for Lexmark Printer (Where can I find older versions)

    Try contacting Lexmark. Dunno where you are but Lexmark.uk are very helpful chaps
  15. Engleberth

    Phaser 350 Sticky Trans-fix roller?

    The Drum/Transfix assembly can be removed as an entity but that would not achive anything. It would very much seem that you are not getting enough oil onto the drum. Check the motion of the maintenance tray lift clutch & cams. Also check the lift arms are they solid or contain a sping in the...

Part and Inventory Search

Back
Top