Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by eliyzfr600

  1. eliyzfr600

    help with static route please

    you have your static routes backwards, also why dont you use routing protocols
  2. eliyzfr600

    hsrp not failing-over

    BuckWeet, yes, as soon as my bgp adj drops i loose my 0.0.0.0 route. my router is getting this route via eBGP, but i can not get my hsrp to detect when i loose my 0.0.0.0 route and failover
  3. eliyzfr600

    hsrp not failing-over

    Yes, the other side has preemt configured...the problem appears to be hsrp not detecting the "BGP Adjacency" loss. Else hsrp works perfectly. Due to the WAN facing int not changing to a up/down or down/down state, hsrp does not react.
  4. eliyzfr600

    hsrp not failing-over

    i have set up the following script but hsrp is not failing over when i loose BGP adjacency. I get my 0.0.0.0 route via bgp however when the route is lost or my BGP neighbor is not reachable hsrp does not failover. My edge router config track 11 ip route 0.0.0.0 0.0.0.0 reachability ! interface...
  5. eliyzfr600

    hsrp not failing-over

    thanks, i was not sure if that was the only way to make it work, does anyone know any good links that could help me with the correct options for object tracking?
  6. eliyzfr600

    hsrp not failing-over

    all, i have a problem with one of my hsrp setups, i have two internet routers with different internet providers each (hsrp), however my "active" hsrp router does not fail-over when it looses BGP adjacency. It fails over when an up/down or down/down state is detected, but not when only the bgp...
  7. eliyzfr600

    877W wireless access setup

    Hello all, Im trying to config my router for wireless access but I dont know where to start, all I want is a simple cofig where my labtop will be able to get an IP and browse the net. I have config my adsl in the wan port and my wired desktop can access the net fine. Im using PAT, and DHCP in...
  8. eliyzfr600

    Configuring 827 with DSL

    Here is the: show run My atm0 int wont come up and I also get a error message bout my ppp being "default" Building configuration... Current configuration : 1056 bytes ! version 12.2 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ...
  9. eliyzfr600

    Configuring 827 with DSL

    hello, I am trying to configure a cisco 827 router with my home DSL, the problem is that when configuring the atm0 interface i dont know the PVC settings nor the type of encapsulation type. I tried getting this info from my provider but all I got was their DNS's address and the cisco support...
  10. eliyzfr600

    Using a Cisco 827 router with my DSL

    thanks for the advice, I'll give it a try.
  11. eliyzfr600

    Using a Cisco 827 router with my DSL

    forgot to add the country, USA
  12. eliyzfr600

    Using a Cisco 827 router with my DSL

    Thank you Andy for the response, However Im still a little confuse, I have pluged in the router to the wall jack. What would be the next step in setting it up to connect to the internet, would I need special software? My ISP dinamic. What commands would I need to enter at the console for it...
  13. eliyzfr600

    Using a Cisco 827 router with my DSL

    Hello everyone, (Setting up a test network) Im wondering if I could use a cisco router 827/827V-4 with my home DSL? The router has 3 ports (console, ethernet, adsl) the problem is that the adsl port is an RJ11 and the port coming out of my modem is an RJ45. Could I just bypass my modem and...
See more

Part and Inventory Search

Back
Top