Recent content by Elca

We have over 11 BD's. It is cheaper than Cisco product. But there are many hardware faulty such as checksum error, packet memory errors. We were sending RMAs of one module per month. It is very critical issue that you have to insert new module and reboot the chassis. In L2 switching, very good...

I had a same experience several times. Just do like this. You can connect the machine through console. On the CLI mode, type "disable telnet" and type "enable telnet". Then you can repair telnet daemon. If it couldn't work once, do it twice or more. It will work. - Elca

In the BootROM Menu, A) Select the primary code image by hitting 1. (Select primary code image) B) After the primary image is selected select k to erase selected configuration. (k is Erase selected configuration) C) Choose d to force default configuration and then "f" to boot on...

Hi, I logged in Summit48i with TACACS user account. So its prompt is >. Summit48i> config account admin Non admin level accounts can only change their own passwords As you see above, When I configure admin account, I can't do that. Can I change user account to administrator account like...

There are officially listed known problems on Sniffer Pro 4.6 Release Note. I excerpted these problems from Release Note. Please see below. And also you can see many bugs at this URL: http://www.thetechfirm.com/ (Information > Product Bugs > - Elca P.S. Sniffer Pro 4.6 Release / Updated...

You can see at this URL: http://www.sniffer.com/education/product-documentation.asp - Elca

Excerpts from the Laura's book 'Advanced Network Analysis Techniques' (http://www.store.yahoo.com/imagitech/adnetantec.html) - Hex reader/Editor - Packet sanitizer - General route tracing tool (e.g. NeoTrace, VisualRoute) - Screen capture utility (e.g. SnagIt) - All purpose TCP/IP utility...

Thanks your reply! Andy, There are two cases. First, I tapped in 3Com Superstack II 3300 with port mirroring (roving analysis). SS II 3300 is connected to IDC's Catalyst 5/6000. Foundry ServerIron XL is connected to SS II 3300. (i.e. Catalyst <-> SS II 3300 <-> ServerIron) It's all switched...

Hi, all! I found Unknown ethertype data on Sniffer trace files. There are many unknown ethertype numbers like below... 7343,7463,3D0D,536C,453D,4233,322E,4158,4E61,4B62,3069,5243,886D,3863,4741,4141,3EOD,6D71,7777,524F,4243,7572,... How can I interpret this frames and what's mean? Any helps...

I found one in relation to annontating the Expert Explain files. It's XPHELP.GID has attributes hidden file with added my annotation. This Global Indexed file was associated with XPHELP.HLP that contains the Expert Explain help information. I think I can back these up with two files. However...

Does anyone have any suggestions on if SMTP Notification doesn't operate? I did set up the Define Actions on the Alarm tab under Tools > Options to enable alarm actions. It's SMTP server name, its port number(25), and the mail recipient's name and email address. It was selected Always on and...

Thanks for your answer! But I can't find my own annotation in XPHELP.HLP. I converted XPHELP.HLP into XPHELP.RTF and I searched my annotation in XPHELP.RTF but I couldn't find it. Any other clues? - Elca

You can deal successfully with Sniffer Full Duplex pod or Shomiti Century Tap or HP LAN Analyzer Tap. It's eliminates many of the problems commonly associated with the use of a switch mirror port: - Switch performance degradation - Inability to mirror errors such as undersize and oversize...

Hi, I used to comments on a Sniffer Expert Annotation. You can annotate some clues into Expert Explain Files by clicking ? (question mark) in Symptoms/Diagnoses. Does anyone have any suggestions on how can I backup/restore my own annotation? TIA, - Elca

Hi, all I can't setup ip address in ATMbook like below: >> si 10.0.0.3 S_errno_ENXIO ip address could not be set Updating system configuration... Erasing Flash Section 86... I think that Xircom NIC couldn't be bind with ATMbook. Has anyone seen anything like this before or have any...