Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by edsuk1

  1. edsuk1

    pda devices

    Lee, you need to setup incomming rules to allow the traffic through your firewall to your SMTP server. I.e Port 443 TCP to your SMTP server to allow the traffic in.
  2. edsuk1

    How to Config Remote IP Phone in a Second Office

    One other thing I have noticed with the system manger under BootP it shows the following: 1 x entry enabled - not ticked Mac 000000000003 Ip address 192.168.16.40 file name nas0-16.bin time ofset 0 There is a seperate entry for the live box with the correct mac and ip address etc Is the...
  3. edsuk1

    How to Config Remote IP Phone in a Second Office

    Do I do that in the Client phone manager or on the IP box?
  4. edsuk1

    How to Config Remote IP Phone in a Second Office

    The IP address are for standard winxp machines with phone manager loaded (clients). No IP phones whatsoever, 1 x 406, 1 x ISDN box (used only for occasional ISDN kit that is plugged in from time to time), 2 x 16 port analog pots, with a seperate PC running the manager software. Yes, network...
  5. edsuk1

    How to Config Remote IP Phone in a Second Office

    Its been a long day, thanks for pointing out the obvious.....I really should read before sending. Any ideas on what the TftpServer logging means, if I click on the Tft log from manager it shows the following: Fri 6/7/2007 10:08:03 : Received BOOTP request for 000fb5fdbbbc 192.168.16.25 ...
  6. edsuk1

    How to Config Remote IP Phone in a Second Office

    Got it, we have some standard analogue phones that are power by a seperate PSU, so this would be the same, albeit an IP phone. Will review the 4621BL phones - thanks for that. Opened monitor, cant see where the Vcomp value would be, any ideas? Also shows TFTP xxx copy of dump below, again any...
  7. edsuk1

    How to Config Remote IP Phone in a Second Office

    Thanks for coming back so quick, Gibsonic, just a couple of points: 1. "external avaya power brick or a standard PoE switch", excuse my ignorance, what is a "power brick" and is it located at the remote site? 2. We can do static ip's not a problem. 3. We do not currently have any IP phone or...
  8. edsuk1

    How to Config Remote IP Phone in a Second Office

    1. We have a second office with a fixed range of external IP addresses, I am looking to install a phone and use as part of the main office system, by calling either way using the extension number, any ideas?
  9. edsuk1

    IP Office 406 Calls Dropping and Remote Office Setup

    Hi TLpeter. Thanks for that: 1. I thought that we were unable to upgrade any further than that of the current version, if I upgrade will that cure the problem do you think. What other fixes are in the upgrade any ideas? 2. Will hunt around. 3. Seems very strange.
  10. edsuk1

    IP Office 406 Calls Dropping and Remote Office Setup

    Hi We have an IP Office 406 with a PRI 30. 1. When a speed dial is used, the number is dialled and rings out for around 15 seconds then the call is dropped and redialled again, this occurs for about 5 times until (by chance) the call at the other end is answered and the person receiving the...
  11. edsuk1

    Sun Storedge D1000 & Adaptec SCSI 29160N Card

    I have a Sun Storedge D1000 c/w 12 x 18.1 Gig Scsi Hard drives and I would like to connect them to an internal SCSI card I have in our server, an Adaptec SCSI 29160N Card Ultra160 SCSI internal. The plug on the rar of the Sun is a 68 pin and the plug on the Adaptec card is 50 pin, if I get a...
  12. edsuk1

    Compaq ML530 Set-up

    Hi Jerry. Thanks for you reply. That gives me some thoughts on how I might deploy these units within our business. Are you saying that the drives automatically Raid, as I am unable to locate any facility to interogate the drives or set-up raid within the box? Cheers
  13. edsuk1

    Compaq ML530 Set-up

    Hi All. Have purchased a Compaq ML530, with 2 x Xeon P3, 3 x PSU's and 6 x SCSI disks (2 x 9.1gig, 2 x 18.2 gig, 2 x 36.4 gig) & a 20/40 DLT. This mights sound like a daft question, I am aware that the disks are hot swap, along with the fans etc, but how do I know if the drives have raid and...
  14. edsuk1

    Compaq raid 3200 controller..imminient failure

    Opps, sorry, I think I have posted this in the wrong place. M
  15. edsuk1

    Compaq raid 3200 controller..imminient failure

    Hi All. Have purchased a Compaq ML530, with 2 x Xeon P3, 3 x PSU's and 6 x SCSI disks (2 x 9.1gig, 2 x 18.2 gig, 2 x 36.4 gig) & a 20/40 DLT. This mights sound like a daft question, I am aware that the disks are hot swap, along with the fans etc, but how do I know if the drives have raid and...
See more

Part and Inventory Search

Back
Top