Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by dobber1

  1. dobber1

    Inquiry: Succession 3.0 to 4.5 upgrade

    Thanks everyone. I will be checking periodically. Keep the ideas flowing. I really do appreciate it. Dobber
  2. dobber1

    Inquiry: Succession 3.0 to 4.5 upgrade

    Thanks for the tip John. It is a larger switch and I verify that I have patches and anything else on floppy. Regards, Dobber
  3. dobber1

    Inquiry: Succession 3.0 to 4.5 upgrade

    Hello Everyone, Just putting a feeler out if any one has upgraded a Nortel 81c switch from Succession 3.0 to 4.5. If so, any pointers, comments, suggestions while planning this upgrade and problems after the upgrade. Thanks, Dobber
  4. dobber1

    500 LINE CONFIG'D AS MCR WON'T GO TO VM

    Thanks to Nortellian, Acewalock, John and everybody. The problem was that I had the FTR set has CFW and not FDN. Also I had to change the LHK on the phones where MCR is appearing from 1 to 2. Thanks again to everyone!! Dobber
  5. dobber1

    500 LINE CONFIG'D AS MCR WON'T GO TO VM

    thanks john, that is also done.
  6. dobber1

    500 LINE CONFIG'D AS MCR WON'T GO TO VM

    Yes, it is MARP'd to that TN
  7. dobber1

    500 LINE CONFIG'D AS MCR WON'T GO TO VM

    I have learned quite a bit from the techs on this board and appreciate all the help. I need help with another problem. I have a 500 line set up as a MCR. I have FNA,MWA AND HUNT TO our vm line configured. However, when I call the number it won't go to voicemail. Any help that can be given...
  8. dobber1

    LD 22 SLT QUESTION

    John, Thanks for the insight. I will pursue this as a license issue. Take Care, Sir
  9. dobber1

    LD 22 SLT QUESTION

    John, Thanks for the help,sir. I did as asked that came up with all the tn's that I can use 20 0 12 1, etc. My switch still reflects 1 analog left. Am I to understand that at this point it is a license issue? Or maybe I'm doing something wrong? Here's a screen shot, and thanks for the help...
  10. dobber1

    LD 22 SLT QUESTION

    Hello Everyone, I'm appealing to all the Nortel GODS for an answer to a question. :-) I added an analog card to my opt.81c. in slot 12 on my superloop 20 0. went to ld 20 created a new 500 line. did a LUU and all the 20 0 TN's pop up...great. that's working. Problem is when I look in load 22...
  11. dobber1

    OSN phone and Message Waiting Light

    YOUR KILLIN' ME...though that probably would work.[thumbsup]
  12. dobber1

    OSN phone and Message Waiting Light

    Thanks JP, this feature is more for the guard to stay alert. Wasn't sure what else to do. If it can't be done without building something; that's fine, also.
  13. dobber1

    OSN phone and Message Waiting Light

    Question, my fellow techs: I have a OSN phone that intercepts 911 calls. The phone is a 3903 and has a NON-DID number on KEY 0 MARP'd. KEY 1 is designated as the OSN key. Is it possible to have the message waiting light flash when this phone intercepts the call? This way my security guard can...
  14. dobber1

    MLUCKIE1 Died Sunday...

    Thanks for the information. Mr. Luckie will be truly missed.
  15. dobber1

    combining 3-500 lines on to 1 3900 phone

    acewarlock and JP, Thanks for all the info. Arrived this AM and found out that the 3 lines are forwarded outside to personal lines for after hours use. Something about our fleet division. Anyways, it appears that the 3 lines will have to remain as is since each line is forwarded to a different...
See more

Part and Inventory Search

Back
Top