Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by dlesap

  1. dlesap

    wav files for annunciator

    Hi all I'm running a CUCM 6.1 and want to set it up to change some tones with recorded messages. Annunciators are configured and registered but i need your help for the next steps: - Installing the wav files in the CUCM - Assigning tone replacement with specific file - Other step? Thanks for...
  2. dlesap

    How can i display the company name on the Phone display

    Hi HmmG3 Isn t it possible to put the company name at the top of the screen above the Line Text?
  3. dlesap

    How can i display the company name on the Phone display

    Sorry i guess my question was not clear: On an idle display i want to show the name of MY company It is possible to have a company logo using xml file but i want an easiest solution please... Thanks a lot to advise
  4. dlesap

    How can i display the company name on the Phone display

    Hi How can i display the company name on the screen of a 7960? I run CUCM 6.0 Thanks
  5. dlesap

    BCM50 and Call Pilot Auto Attendant

    Hi I encounter the exact same issue than the one described in this thread: thread1361-1255985 ...but i still don't find any solution. The incoming and outgoing trunk is the same It's an analog trunk unsupervised. After coming into the auto attendant menu, then press 2 or 3 for joining an...
  6. dlesap

    i2050 licensing failure

    You're right... I'm going back to rls 2 :-(
  7. dlesap

    i2050 licensing failure

    Hello i run a cs1000E rls 4.5 I encountered a problem with all my Softphones i2050 when trying to register to the SS. A "Licensing failure" message appears before the registration is granted. It's not a CS IP users licenses because the phone is already created. Looking in the i2050...
  8. dlesap

    MIRAN

    In the Miran administration windows select A0 or A1 as the source. The external source must send an audio signal on the specific analog source 0 or 1
  9. dlesap

    Touchtone\Keypad tone across QSIG link via Cisco

    Hi The EES is for sure working on the QSIG. Then from the router to the IP network, the EES signaling have to be tandemed into H245 tunneling protocol. The way to prove it's working or not is to sniff the outgoing port on the router using Ethereal or any other sniffer and search for H245 data...
  10. dlesap

    Unable to view gateway entries in NRS

    Try with IE rls 6 A patch in the deplist also solve that issue
  11. dlesap

    VOIP Fax options on Option 11c

    Adding an IP ATA might be the solution. But after many tests i can say that you will experience many problems. Depending the originating and destination fax machine brand that connection will not work. Canon faxes are really incompatible... The other solution is to install a Media Gateway in...
  12. dlesap

    Meridian Mail 12.11 Install Tape

    On another Mail rls 12 system
  13. dlesap

    Opt 11 onboard telephone firmware

    Depending the SW rls, you can eighter load a "loadware" file from the pdt or load a new psdl file that required a sysload. These files are accessible from the Nortel Web site
  14. dlesap

    Page Access Override?

    Isn't the Break In (BKI) Key of M2250 gives the ability to freed the trunk?
  15. dlesap

    MSDL DNUM Assignment

    I already try the same configuration but it doesn't apply while the paddle board is inserted. The way to save DNUMs is to use External MSDL instead of Daughterboard MSDL

Part and Inventory Search

Back
Top