Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations wOOdy-Soft on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Recent content by dladuron
-
Netfinity 7000 boot problem and remote access
I received a SMBUS error 3-3-2 after shutting down and restarting a netfinity 7000 M10 server to replase an external UPS. I have followed the procedure listed in the IBM manuel. unfortunately I do not know how to remote access the sys logs and only assume the problem is the VDF card based on... -
changing ground start to loop start - POTS lines
YES It now allows calls to come in1 Infortunatly it does not call out. I can her it dial (pusl) on the trunk card but nothing. Any ideas- dladuron
- Post #48
- Forum: Nortel: CS1000 (Meridian) systems
-
changing ground start to loop start - POTS lines
sorry one more question before I move forward 1) do I remove the truncks (ld 16 out) or just ad a new one?- dladuron
- Post #46
- Forum: Nortel: CS1000 (Meridian) systems
-
changing ground start to loop start - POTS lines
Ok going to follow your directions - one last question - how do I termin the ATDN as I want the system directory to come on not an individal phone- dladuron
- Post #44
- Forum: Nortel: CS1000 (Meridian) systems
-
changing ground start to loop start - POTS lines
ok sounds like I have to rebuild As I have never done this before any tips 1) how do I delete (out the cots) 2) I assume I can use teh same data that is already layed out above? FYI DIP does see the trunk but that is all- dladuron
- Post #41
- Forum: Nortel: CS1000 (Meridian) systems
-
changing ground start to loop start - POTS lines
ok 1) Clipping on to the punch down block that leads to the switch - I get dial tone and can send and receive calls. 2) Is there anyother place then the CLS (LD 14)that I need to change DTN to DIP?- dladuron
- Post #37
- Forum: Nortel: CS1000 (Meridian) systems
-
changing ground start to loop start - POTS lines
Lets review The PBX was originally installed with POTS lines type ground. All functions worked including call in call out voicemail, conf and full routing etc. We move from carrier POTS to VOIP which are type loop. Leaving the system with its original configuration we are able to call out...- dladuron
- Post #35
- Forum: Nortel: CS1000 (Meridian) systems
-
changing ground start to loop start - POTS lines
where do I go to find routing for incoming?- dladuron
- Post #33
- Forum: Nortel: CS1000 (Meridian) systems
-
changing ground start to loop start - POTS lines
ok I have changed the TARG with LD 16 ( do I need to do a command in LD 32 to make this become active? I still do not see anything in LD 14 for TGAR (nor in LD 20 - prt) What seems to be the problem is that while it is in loop start the truck card does not serach for an outside line to call...- dladuron
- Post #31
- Forum: Nortel: CS1000 (Meridian) systems
-
changing ground start to loop start - POTS lines
ok I have changed the TARG with LD 16 ( do I need to do a command in LD 32 to make this become active? I still do not see anything in LD 14 for TGAR (nor in LD @) - prt) What seems to be the problem is that while it is in loop start the truck card does not serach for an outside line to call...- dladuron
- Post #30
- Forum: Nortel: CS1000 (Meridian) systems
-
changing ground start to loop start - POTS lines
Route ld 21 rout= 1 targ= ld 21 rout= 2 targ= 0 1 Where do I find tgar you are talking about When I run LD 20 to see the set I do not see targ listed. Where should I look?- dladuron
- Post #28
- Forum: Nortel: CS1000 (Meridian) systems
-
Can A Meridain Option 11c take pots lines
Seems that by connecting the POTS to the trunk card they are working for outgoing as long as the lines (LD 14)are configured in grd. However, when configuring them in loop mode they quite working. I am sure this is the tweaking you are talking about.- dladuron
- Post #8
- Forum: Nortel: CS1000 (Meridian) systems
-
changing ground start to loop start - POTS lines
a little guidance here please! Know that one is on LD 14 and the other is on LD 16 but to review this need to know how.- dladuron
- Post #26
- Forum: Nortel: CS1000 (Meridian) systems
-
Option 11C working with VOIP
ok LD 14 SIGL = loop ATDN = 5999 ok LD 16 ROUT = auto Where would I find this "atdn to the answer dn on the trunk"- dladuron
- Post #8
- Forum: Nortel: CS1000 (Meridian) systems
-
changing ground start to loop start - POTS lines
no switches on the card only jumper and these are set as Loop CO- dladuron
- Post #23
- Forum: Nortel: CS1000 (Meridian) systems
