Recent content by Dimpa1

Howdy People!!! My user is running a simple SQL query (that's what he says) on a Austin server 10.0.144.179 to a Houston server 10.0.102.4. It takes 3 sec if he does it from the same LAN, but it takes 6-8 minutes going through a WAN. I have a sniffer trace that shows mostly "Bad Checksum" What...

I’m trying to find some freeware that I can monitor CRC/etc error on an IBM NIC. Does anyone know where I can find it? Thanks.

I’m trying to find some freeware that I can monitor CRC/etc error on an IBM NIC. Does anyone know where I can find it? Thanks, Dimpals

I download it (windows) and I tried using the iperf.exe but I cant type anything on there. Am I suppose to install it on 2 pc, 1 at each end?

I get this for my serial int, which is generic for all serial so it doesn't help. I am not at that location either, I can telnet to the router only. Is there some shareware I can use for bandwitdh measurement? Serial0/1/0 is up, line protocol is up Hardware is GT96K Serial MTU 1500...

I have a cisco router connected to a vsat, which is suppose to give me 128K but it seems a lot slower than that. What tools can I use to see how much bandwidth I have on a private circuit? Or is there any command on the cisco router that I can take a look at?

I have a cisco router connected to a vsat, which is suppose to give me 128K but it seems a lot slower than that. What tools can I use to see how much bandwidth I have on a private circuit?

I'm trying to look for a consultant company to come in and do a demo of websense and implement it if we decide to go with it. Does anyone know where I can find a list of companies that would do this in Houston, TX? I have more than 20 locations. Approximately 1000 users. My 3 main locations...

10.0.1.1(pix1)~~~(www)~~~(pix2)10.0.2.1--.3(lnksys)10.0.3.1 I have a created a vpn tunnel on both pix. From pix1 network I can hit pix2 network, but I cant reach anything behind the linksys. I think this is because the linksys nat every node behind it to 10.0.2.3. I cant seem where the nat...

Hello, I have an exchange server on my internal network 10.0.2.1 and I translate it to 222.1.1.1 on my pix firewall and also created an access-list to open up a certain host to be able to access the exchange server from the internet. I am using an air-card to connect to the internet. And have...

Thanks for the response. It turned out to be a PC issue, which I sort of knew all along, but didnt have proof, until I had to fix someone elses problem for them, which they blamed on my WAN! Ok, I have found out that on Windows Firewall, for NetRC, the scope is set to allow “my network only”...

We changed our router from 3640 to 3845. The configs are similar. However, NetRC (similar to remote desktop) does not fully function through the WAN (T1). When I use NetRC to poll the pcs on the remote network, it only show up to have 27 hosts, which there should be over 100. If I tell my...

I need a diagram to know about the routing. We have a fully mesh MPLS. We had MPLS installed in our network and was told to use bgp, however that didnt work for us (it messed up all our routing tables since we were using eigrp). So we told our provider (MCI) we want to use statics and it is...

no isakmp policy 10 group 1 isakmp policy 10 group 2

Found this info on cco. Couldnt find info on router specifically, but on the switch instead. See if the router supports [service compress-config]. hope it helps. Managing Software Images and Working with Configuration Files on Catalyst Switches...