The local backup was overwritten next day by the scheduled daily backup. I have an older external full backup which I will need to use. Unfortunately I have then to update a lot but at least I should be able to handle the dilemma.
Another question I have:
At the moment both LIMs are still...
Old relvol is unfortunately too old.
If I at least could get either the missing program units for successfully executing the following command copied over to LIM1:
<lcddi:tab=fdt,frct=8,pre=2995,tzone=1&&9;
WAIT
WAIT
FAULT INTERRUPT
MESSAGE FROM OPERATING SYSTEM:
RELOAD REQUESTED
RELOAD...
Thanks fcpli for your input.
CNPIP does actually exist:
CNPIP:{[}UNIT=&5{|PUNO=&5]};
Anyhow, new problem at LIM1 is now that my authorization codes aren't working anymore.
I did a backup prior to blocking and ending LIM2. Would you suggest to restore with LADAI or
with LALRL:LIM=2;
rgds, devplan
I have 2 LIMS (BC10CNA129/R1A) which I would like to divorce gracefully.
In other words, I want to de-commission LIM 2.
On LIM 2 I have removed any extensions, group hunting, group pickups and operators and any traffic recordings and common public directory numbers.
Then I did...
whosrdaddy:
to answer your questions:
*22#1044# (procedure executed) follow-me to ABB
*22#2044# (procedure executed) follow-me to ED
*22#2042# (procedure failed) follow-me to ACD group
*21*2042*1044# (wrong format) ACD grp follow-me to ABB
*21*2042*4709# (procedure failed) ACD grp follow me...
Thanks, changed now ACD params as given by you.
<RODDP:DEST=2044;
EXTERNAL DESTINATION ROUTE DATA
DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE
2044 8 0005000000000250000 4 5 0 20442044
END
<ROCAP:ROU=8;
ROUTE CATEGORY DATA
ROU SEL...
Thanks for the fast replies.
fouesnant:
Yes, when I dial directly 2044 it works.
My route goes out on an ISDN30 trunk into an asterisk box via DIGIUM TE122P.
rodap:rou=8;
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
8 SL60 H'00000000 H'15400000 H'02010000 NO...
I might be beating a dead horse but I have tried x ways to get an external call diversion with BC10 to work.
My 1st attempt was like this:
cdini:dir=4709,div=2044;
(4709 is an EX)
(2044 is an ED)
<kscap:dir=4709;
KEY SYSTEM CATEGORY PRINT
DIR TRAF SERV CDIV ROC ITYPE...
I have BC10CNA129/R1A and would like to connect an analogue phone with integrated answering machine (f.x SIEMENS Euroset 5035) to an ELU29 (ROF1375339/1 R7A).
This should be simple. I would like however to have the CID for the incoming call displayed too.
I read some posting concerning CID on...
Hi dstrang1
Actually like that:
External calls to the FAX come in on my MD on route 1 and needs to go out again on route 1 (as the new FAX nbr 89103286).
Not out on route 8, which it has been previously, that routes to my asterisk box. [pipe]
rgds, devplan
Thanks for the replies.
Probably I wasn't clear about my setup.
We have two LIMs that can call each other internally (like 82xx) and each extension can be called with an outside prefix of 1234 - thus the external complete number to reach ext. 3200 would be 1234 3200.
The extension series 32xx...
I have BC10 and use the numtyp ED to have incoming calls routing over a DIGIUM E1 card that sits in an asterisk box and then routing the calls to another building to an asterisk server which works fine.
However - due to the problem of receiving and sending fax over voip, I have been asked to...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.