Recent content by ddimitrie

I need to have the required digits necessary to out call from a mail box to a cell phone using line pool. So Far: The 2 ports on the star-talk are not resricted The 5 lines in the line pool are not resricted The class of service is (1) which alows out calling Notification is turned on (the hours...

Have set up sip trunking between a MITEL 3300 ICP with NuPoint Voice Messaging and a Nortel CS1000. Seems to work for the most part, but wondering if anyone has come across the following problem: internal call from the CS1000 on an IP phone to the MITEL - to an IP phone. If the call goes to...

Have set up sip trunking between a 3300 ICP with NuPoint and a Nortel CS1000. Seems to work for the most part, but wondering if anyone has come across the following problem: internal call from the CS1000 on an IP phone to the MITEL - to an IP phone. If the call goes to voice mail, the caller...

What release level are you on, on the 3300 ICP? We will be on MCD 4.2 & we're on 6.0 on the CS1000. Didn't get the doc, can you check the address ---- ddimitrie city windsor on ca thanks darlene

I can be reached at the E M A I L that starts with my username (9 characters) followed by an at sign. Domain name is city followed by a dot, then windsor, followed by a dot, then on, followed by a dot, then ca Thank you Darlene

Don't get me started - I started working full-time in 1979 for Burroughs - mainframe computers - in technical support - in 1994 I made the jump to telecomm, quite by accident - the guys in the Property department retired and the powers-that-be thought, hey, you know, cabling for voice and data...

I'm a long-term Nortel customer; new to MITEL. We're putting in a 3300 ICP (MCD 4.2) and want to connect to our CS1000M via SIP trunking. My understanding from MITEL is that this is possible as of CS1000 software release 4.5. Anyone have experience with this or know of documentation? Thanks...

thread798-1006400 Had a similar problem today -- turned out I had some CLID entries missing - so instead of the calling id number, the DN got sent out. This prevented sets with the missing CLIDs to not be able to make toll-free calls. To complicate matters, we use a different telco than the...

Thank you; I hooked up the external power; it can run either way --- I do get messages now. First it says: LOADING: Initializing bootram then LOADING: Loading boot parameters and there it sits --- Now I'm back to the original problem -- we had 2 i2033s do this today upon reboot.

I have an i2033 that won't boot. I think I unplugged the network jack while it was downloading firmware. Is there any way to resurrect this phone? I know the jack is live - I hooked up an i2002 and it works. Darlene

Thank you very much for that suggestion. I will try adding the DMI to the existing RLI ---- I got it working by removing one of my ROUTs -- it had a DES of WAT --- but I am getting errors now --- I think I will put back the ROUT --- add the DMI to the existing RLI, CTYP NPA and see how that...

On the advice of Allstream, the new carrier; and TELUS, our support vendor -- we were told that nothing on the PBX needed to change, that Allstream would configure the PRI just like it was on Bell --- TELUS was adamant that there was no programming changes needed, that they didn't even need to...

Just switched carriers - Bell to Allstream. Can't make outbound long distance calls. Allstream says to change "tagging on outbound calls" from OUTWATS to National or Unknown. Any ideas on where I do this?

I set BDCT to YES --- but can't figure out where to set the number of connections on the trunk. So then I tried to set it back to NO and it tells me that "SCH0062 The change of a Music broadcast route to a non broadcasting route, is not allowed." I do not have ISMs for RAN CON or MUS CON ---...

I have MOH defined as follows, with 1 TN 20 0 10 1: REQ: prt TYPE: rdb CUST 0 ROUT 43 TYPE RDB CUST 00 ROUT 43 DES CYMOH TKTP MUS NPID_TBL_NUM 0 VTRK NO NODE ICOG OGT SRCH LIN STEP BDCT NO ACOD 7143 TARG 01 CLEN 1 OABS TIMR ICF 512 OGF 512 EOD 13952...