Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by DarinR

  1. DarinR

    Magix - Disconnects/Dial-Tone Voice Mails

    Thanks, Merlinman! Do I need to match the hold disconnect timing with the telco, or just set it to short anyway?
  2. DarinR

    Magix - Disconnects/Dial-Tone Voice Mails

    Before I start, let me say that I've poured through this forum and have found some possible issues/resolutions, but I'm still having the problem. So, to the experts I've come: Magix 2.0 V9.0. DuVoice DV2000 messaging. 3 - 2-way copper trunks (local and LD through Qwest) Symptoms: * Random...
  3. DarinR

    10 digit dialing change

    Once again, the search function finds a solution for me! I've already added the 1458 NPA (458 being the new OR area code), and was curious if simply adding 541 and 458 as NPAs would allow for both 7- and 10-digit dialing. You guys rock! I know there is no new information or a question here...
  4. DarinR

    Bad Analog Card?

    How about this for luck ... Went to the switch room to disable the system monitor to see if that would bring the ring generator back up. Decided I would first swap out analog cards (remember, had one that wasn't ringing, one that wasn't working at all). Disabled the non-working card, and as...
  5. DarinR

    Bad Analog Card?

    Thanks, everyone. I'll try disabling the system monitor this evening or tomorrow morning and see if that does it. One question, though ... hypothetically, let's say the whole column goes down as StanleySteamer pointed out could happen ... what will I need to do to get everything back online...
  6. DarinR

    Bad Analog Card?

    How do I disable the system monitor? I presume that if I do that and the ring gen comes back up, then it is the system monitor that is failing? By the way, repeated the ring gen and its still not working ... Ready to order a new one if the system monitor doesn't provide any answers.
  7. DarinR

    Bad Analog Card?

    Looks like a combination of ring generator and line card(s). Tested some other non-functional lines on another analog card on the same shelf, and none of them are working at all. First thing I noticed when I walked in the switch room was a red light on the front of the cabinet. I suspect it...
  8. DarinR

    Bad Analog Card?

    Haven't had a chance to get to the switch room, but before everyone starts laying odds, here's some more info: TN 4 1 5 3 is my desk phone (2616), and it rings fine. TN 4 1 14 4/6 are the two lines that aren't ringing. Pretty much rules out a ring generator on the shelf, doesn't it? Found a...
  9. DarinR

    Bad Analog Card?

    How about 10 to 1 in favor of the ringing generator :-) Maybe just wishful thinking ... should have a chance to check today.
  10. DarinR

    Bad Analog Card?

    Option 61C I have a fax line that is not ringing. Has dial tone, can dial out, two-way talk is fine. And, if I clip a butt set on the line and dial from my cell phone, I can answer in talk mode (even though the butt set doesn't ring). After some testing, I discovered that there is another fax...
  11. DarinR

    ERR5306

    Thanks for tips. GHTrout, you are correct ... both were set to XFD. Changed to CLS XFR. Alarm tech should be on-site today ...
  12. DarinR

    ERR5306

    Thanks to all of your collective genius, I was able to troubleshoot an issue that has been bugging the heck out of me. I have an analog line serving a fire panel, and just a few weeks ago began getting reports that the panel was not sending its regular reports as it is supposed to. Checked LD...
  13. DarinR

    Probably an easy one ...

    Yeah, the "flash" button is a duration programming only ... it is actually recessed such that you have to use a pen or something to press it. So, I went old school. Connected a call, hit the hook (as if to hang up the phone, but only briefly), got the stutter tone, dialed the next number, and...
  14. DarinR

    Probably an easy one ...

    I understood that to be only a flash duration programming key - thus its covert location. I'll take another look, though. Thanks!
  15. DarinR

    Probably an easy one ...

    Just realized this set has CLS MBXD. Would MBXA make all my problems go away?
See more

Part and Inventory Search

Back
Top