Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by damocles13

  1. damocles13

    having trouble w/the "li" cmd

    thread690-1394628 From CBB's previous post: List trace station xxxx/x An example would be list trace station 1234/7. This would activate button 1 on extension 1234. Note: you have to add 6 to whatever button you want to press, button 1 is 7 button 24 is 30 etc… I'm running CS1000M Ver 3621 R7...
  2. damocles13

    A designator on the end of a TN

    Thank you! Give a man a fish and he will eat for a day. Teach a man to fish and he will sit in a boat all day and drink beer!
  3. damocles13

    A designator on the end of a TN

    I have several TNs that I'm looking at that have an "H" after the TN. I do not know what this means. I've asked several co-workers; both with more experience than I and they are just as in the dark as I am. Is there some one out in Tek-Tips Land that can enlighten me? I have included two of the...
  4. damocles13

    deleting commands on a 4500 series switch

    Thanks guys, The switchport trunk native was the last NA's attempt to control untagged frames. I hope the "no" command works for the qos and tx-queue that was left behind. Thank you again.. The revolution will not be televised!
  5. damocles13

    deleting commands on a 4500 series switch

    I have an 4507R with a port that does not need the residual commands left by previous admins. interface FastEthernet6/12 description HR Rm215 P639 switchport access vlan 10 switchport trunk native vlan 999 switchport mode access speed 100 duplex full qos trust dscp tx-queue 2...
  6. damocles13

    Vlan doesn't work

    I have a problem with configuring a vlan on a cisco 4506 switch. I've gone transparent created the vlan saved the ru to st; switched back to client, but still a self-assigned address. This switch is client, I've already created the vlan in the switch that is the vtp server. Keep in mind I'm new...
  7. damocles13

    Trunk between 2950 and 4500

    Cluebird, thanks a bunch. It was the Cross Over that got me. Its always the simple stuff!!! Thank you , again. The revolution will not be televised!
  8. damocles13

    Trunk between 2950 and 4500

    I have a Cisco 2950 and a Cisco 4506 and I cannot get the trunk between them to work. As I am new to this please do not hesitate to ask the simple questions! The config on the 2950 port: interface FastEthernet0/1 description Trunk to CoreSwitch switchport trunk encapsulation dot1q switchport...
  9. damocles13

    Need to access a HP2524 Procurve

    I figured it out, finally, and you are correct (thanks). I made a null modem cable and it worked!! I appreciate the response. They mostly come at night, mostly
  10. damocles13

    Need to access a HP2524 Procurve

    I have a HP Procurve 2524 switch. I have tried to console in by Cisco rollover cable attached to a USB converter (I'm using a Mac). I cannot get Zterm to work. I've done the pointy object approach with the reset and clear buttons, but to no avail. Any and all suggestions would be appreciated...
  11. damocles13

    DSL shipped over 66block

    I got it figured out my grn and white from the grn needed to be reversed on the 66 block, my bad. Thank you anyway if you were going to respond. They mostly come at night, mostly
  12. damocles13

    DSL shipped over 66block

    I'm trying to get a DSL in one building shipped over my internal phone line (via 66 block) to another building. My pinout does not seem to be working. 1,2,3,&6 1= white/orange 2= orange 3= white/green 4= green I'm using 568b from the DSL modem to the 66 block with the pinout above, then the same...
  13. damocles13

    Finding the IP of my Cisco switch

    Ok, I see where they are now. Hey burstbees I saw one of your posts a while back with a guy who could not connect via telnet into his router. I do not want to incur your wrath! Thanks for pointing out my gaff. They mostly come at night, mostly
  14. damocles13

    Finding the IP of my Cisco switch

    Thanks guys, I appreciate your time. They mostly come at night, mostly
  15. damocles13

    Finding the IP of my Cisco switch

    I've got a cisco 2950 switch that I need to find out the IP address. The NA is no longer around and, as you can tell, I'm new to this. I would like to thank you in advance... BTW, I've already reset the psw so I can get into it. I just do not know the exact command to get the info. They mostly...
See more

Part and Inventory Search

Back
Top