Recent content by CyberJMC66

I am unable to get Windows Media Player content that uses the embedded WMP (6.4 or mplayer2.exe). If I bring up a stream under IE, I get some of the Media Player buttons grayed out and no sound. If I bring up a stream under Mozilla Firefox, I get a message indicated the plug-in executed...

I have the following configuration (and have posted this question before); Cisco 3620 running IOS 12.2(13) with IPSEC/FW Two ethernet interfaces - One to public Internet address (NAT outside) *** Have four contiguous IP addresses on outside One to internal RFC1918 address (NAT inside...

Here's a wierd one for the forum. I recently upgraded my 3620 to "IOS (tm) 3600 Software (C3620-JK8O3S-M), Version 12.2(13), RELEASE SOFTWARE (fc1)". I had username's setup with autocommand commands to 'access-enable host timeout 5'. They worked great prior to the IOS upgrade...

I know this is a tip/trick, but I can't find the solution... I have some messages sitting in outbox folder of Outlook 2002. I am in "Work Offline" mode and not connected to network with exchange server. I keep getting popups indicating Outlook is trying to connect to Exchange...

Wasn't sure which forum to post this in. Has anyone had the requirement to send syslog entries to multiple destinations from Cisco routers and switches? Any ideas and suggestions would be appreciated. Thanks in advance

I have used the following command successfully; ip nat inside source static esp 10.x.x.x interface ethernet 1 Now, what if I want more than one VPN client running from inside? (Do not want to specify 10.x.x.x?). Do I use 0.0.0.0 notation?

I had used that before - but I was filtering - which was the problem. Thanks! I would like to re-enable my filter, I suspect I need to allow IP from my VPN service provider huh? Ports 500?

I am not sure which crypto commands to use, if any. That's what I am asking...

I have the following configuration; Cisco 3620 running IOS 12.0 with IPSEC/FW Two ethernet interfaces - One to public Internet address (NAT outside) One to internal RFC1918 address (NAT inside, 10.x.x.x) No access lists (for now while I am troubleshooting this problem). Most features of...

http://www.netdiag.com/a_fool_with_a_tool_is_still_a_fool.pdf

I would implement a discovery filter to limit what is discovered. Your message may be from your netmon.lrf file. Did you hit return after the PAUSE keyword. That whole line should be one line with no returns in it.

I am certified in both Openview and BMC Patrol. I know folks that know CA and Tivoli. I can tell you one thing for sure from my experience; If you don't implement the processes (philosophy, process, procedures) with these tools, they will all fail miserably to deliver expected results. HP has...

If you want to limit NNM discovery by host names (DNS, Hosts), the best way is to put the fully qualified DNS name into a file, then use a filter set reference to that file. For example; Sets { Servers2bMgd "" { /filtersets/servers.fs } // File name and extension can be...

Check out the following book; OpenView Network Node Manager: Designing and Implementing an Enterprise Solution by John Blommers Paperback - 352 pages 1 edition (September 13, 2000) Prentice Hall PTR/Sun Microsystems Press; ISBN: 0130198498 ; Dimensions (in inches): 0.94 x 9.26 x 7.05 I would...

I have setup a Courier V.Everything modem on the Aux port of a Cisco 3620. Purpose is to provide dial-in support to the router. However, when I dial in, I get the following output; ============================ rtr> rtr> rtr>RING Translating "RING"...domain server (64.47.64.19)...