Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by cvrbob

  1. cvrbob

    Headset on 4412 (Merlin Magix)

    you need a headset status button, and a hangup button in central programing
  2. cvrbob

    Merlin II AT&T System - help request with reward...

    go central program put in your console sta , then look at what the lights show , look for green , which you will touch read the display just dont hit enter , if the light goes out ,touch again to put the light back on, what is the feature ? then go the other station that are ringing and do...
  3. cvrbob

    Merlin II AT&T System - help request with reward...

    actually with the console you have you do not need to enter any codes slide switch to p (program ) touch conference 2 times in the display should show something like system, lines , centel , and more with the buttons under neath as the choice the data and programing is kept in the...
  4. cvrbob

    Merlin II AT&T System - help request with reward...

    yes its probably controlled under follow me, there must be a button lite on the console to control it ,see what you find in your manual about how to set it up , it made be under groups But MM idea to put in a release Legend 7.0 is the best way to go, I upgraded my last 2 Merlin 11 in the mid...
  5. cvrbob

    Merlin II AT&T System - help request with reward...

    thinking back its been a while to change the ringing , is thru the system programing, it was slide the switch down to p touch the conference 2times, them i believe the first intercom is for telephone programing button and the second is for system , read your display when you locate which one...
  6. cvrbob

    Merlin II AT&T System - help request with reward...

    on the left side their is a slide switch, slide it down to the p ( program ) touch a line button dial * 37 ( ring ) to all lines , then return switch to center position *36 is delay ring *35 is no ring
  7. cvrbob

    Merlin Legend BTMI

    you can try the gpa but it may not have the volt to push it that distance, as long as it is a BIS set, no HFAI sets you can also if it is a Bis on a legend you can wire a 48V transformer at the phone jack on the white green pair , using your blue & orange pair to use in the 2 good feed pairs...
  8. cvrbob

    Processor losing power

    I suspect one of the modules is having a power issue, trying to diagnose is hard unless you are there to see which module is loosing power before the system goes down and reboots, but it is a crap shoot ,some time the Partner PC diagnostics in the Partner PC Administration program will show it...
  9. cvrbob

    Partner ACS 8.0 volume issues

    did you check the loop current ?
  10. cvrbob

    Merlin Mail R3 "Please return call" 7000 messages

    it looks like someone has posted a message from 7131 to those stations and using the return call feature if I remember right. try and find a manual to explain its been to long, the other I remember is #751extension number of the posted message but it is the personal posted message sorry can't...
  11. cvrbob

    PAartner acs 509 processor giving a very loud exccesive loud beep after a page is sent from an analo

    check your stations in calling group 1 for feedback *70 IS paging and members of CG 1
  12. cvrbob

    Trying to get trunk to trunk forwarding working on Legend in key mode?

    In a key system you have no pool ,that is why you get the error 70 pool = 9 ,in a key system you use the line or trunk using 801 to 880 that you using to dial out, Forward : trunk (using 801 to 880 Programmed for principal user ) destination number and then the #
  13. cvrbob

    Trying to get trunk to trunk forwarding working on Legend in key mode?

    it's been years since I've done it , i believed the incoming line needs to have a principal user assigned & delay forward at the extension , and in the Key system you use line number 801 or what ever trunk 808 destination number and the #
  14. cvrbob

    Can I insert a PCMCIA into a Partner ACS R8 while power is on?

    forgot to tell you make sure you take off auto backup after to not get a backup error

Part and Inventory Search

Back
Top