Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by corsyl

  1. corsyl

    strange duplex behavier at sfp

    to maksg Thank you very much for your information. This was the key to solve the problem! In my search I missed this command "media-type". Thank you again, it much appreciated.
  2. corsyl

    strange duplex behavier at sfp

    burtsbees, below you will find the sh run, sh cdp neigh det, sh interfaces stat. As you can see the 2960 gi0/2 100MB SFP is in half duplex mode. I really wonder why! ASW2> ASW2>en ASW2#sh run Building configuration... Current configuration : 3880 bytes ! version 12.1 no service pad service...
  3. corsyl

    strange duplex behavier at sfp

    burtsbees, I'll do a sh run etc. today. To your last reply: I have not a Gbit SFP but a 100Mb SFP module (GLC-GE-100FX) in the 2960 because the 2950C is 100Mb only. According to the Cisco documentation this module is compatible with the 2960...
  4. corsyl

    No vlan traffic between 2 4500's except Vlan1

    sorry guys for the delay. I have solved the problem. The PVID was not set correctly.
  5. corsyl

    strange duplex behavier at sfp

    Hi, We are interconnecting a 2960 equiped with a cisco 100MB FX SFP to a 2950C. We get errormessages telling me there is a duplex mismatch: 00:36:48: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on GigabitEthernet0 /2 (not full duplex), with ASW2 FastEthernet0/25 (full duplex). I have...
  6. corsyl

    No vlan traffic between 2 4500's except Vlan1

    Hi all, I am trying to setup 3 Vlan's and ports on 2 switches. What I have done: switch#1: vlan1(default), Vlan2, vlan3 switch#2: vlan1(default), Vlan2, vlan3 switch#1: port 1/0/1, hybrid, untagged vlan2, tagged vlan3 port 1/0/2, hybrid, untagged vlan2, tagged vlan3 communication between port1...
  7. corsyl

    BCM50 to CS1K NRS using SIP trunk

    Hi all, I have a question about sip trunking from a BCM50R3 to a CS1K NRS. This is all new to me so forgive me if it's a dumb question. We have enabled 4 sip trunks at the BCM50. We use a 4 digit numbering plan. What we need is to be able to call another site which has a 4xxx internal numbering...
  8. corsyl

    Unable to register 12XX sets at BCM450

    Thanks all, For now I am still having trouble, even on a BCM400 4.0 I have opened a case at Nortel and awaiting for answers. I will update you with info if available.
  9. corsyl

    problems stacking BES220-48T-PWR switches

    Hi all, I am having problems stacking BES220-48T-PWR switches. What I have done: - checked if firmware of both are the same: OK - Set switch 1 at the back to "base" - Connected both switches from up-to down port and from down-to up port. In other words I created a loop. (according to the manual)...
  10. corsyl

    Unable to register 12XX sets at BCM450

    @gwebster: Thanks, is it possible to load the firmware outside the BCM? I mean, running TFTP or something on my laptop and load the firmware from there? @snowman50: Thanks, Ill give that a try!
  11. corsyl

    Loops not available in BCM450

    @ Snowman50: We have set the card in resourses correctly. Status is enabled but the lines for the first loop are set in BlocB by the system. @ DBrewsky: We do use routing for the PRI for outgoing calls. We need the BRI for a GSM gateway. So we created a route to this BRI for mobile numbers. To...
  12. corsyl

    Unable to register 12XX sets at BCM450

    We are unable to register 12xx sets to a BCM450. The problems we encouter are as follows: BCM is setup as DHCP server. registering 11XX sets => no problems registering 200X sets => no problems registering 12xx sets => trouble When connecting the 12xx set the set displays information: Loading...
  13. corsyl

    Loops not available in BCM450

    At the moment we are configuring a BCM450 and we encounter some problems: We have a BCM 450 loaded with a DTM module and a BRI module. According to the documentation we have to assign lines to the modules which we did: DTM (Main MBM4) => lines 91-120 BRI (Main MBM3) => lines 61-68 All...
  14. corsyl

    trunking problems connecting a 2960 to a 2950

    Cluebird and Burt, Thanks for your replies. It makes a lot clear to me. The router we will use will be a cisco and will be used as a router on a stick. Configuration will be no problem. Thanks again.
  15. corsyl

    trunking problems connecting a 2960 to a 2950

    Burt, if I understand right you say IF I use different VLAN's to seperate 2 networks I always have to use a router? So, the only solution is to create VLAN200 in the 2950 as well to get it work if I don't have/use a router? My confusion is propably that I have set the same situation for...
See more

Part and Inventory Search

Back
Top