Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by cmp241

  1. cmp241

    problem with extensions in office manager 3.0?

    Hello everyone, I replaced a 403 with a 406 and load the 403 config file in the 406. But for some reason the extensions in office manager do not match the extensions on the patch panel. For example, what's plugged in the 1100 slot shows up as extension 1107. Any ideas on how to configure office...
  2. cmp241

    Fault code 274, Digital Trunk, clock Malfunction?

    Hello again everyone, I have a trunk line coming into the TLU76/1 and this is the fault code: Fault code 274, Digital Trunk, clock Malfunction. I am assuming that I didn't setup the synchronization, frame, or rate, something having to do with the clock rate or speed for the specified route in...
  3. cmp241

    ISDN setup procedure?

    Hello, I am in the process of setting up an ISDN (Q.921, ETSI) connection. Can someone tell me the sequence of commands and boards that play an integral part in setting up an ISDN connection? Using board TLU 76/1 Here is what I gathered so far. I. TLU Board configuration • CNHUI • ROCAI •...
  4. cmp241

    Call failure, please help, asap

    Thanks alot jml2665, the problem is fixed. Hannibalik, fortunately for us we didn't encounter your problem.
  5. cmp241

    Call failure, please help, asap

    when making a call, the call fails and never connect. Below is the printout from Sysmonitor. You can see the call begin, but then it goes down hill from there. I am assuming this line, "11mS PRN: Line 5: Manual: Line Loopback Up" is part of the problem, I never saw Line Loopback Up before, what...
  6. cmp241

    Configuring Ethernert Port as MML Port

    Problem solved, I used the IOEQI command. Thank to all for rushing to answer, lol.
  7. cmp241

    Fault code 106?

    Alright guys, no need to reply. The remedy was to set the calendar ( time and date) of all things, lol. Nice to know the MD 110 is so anal. Thanks for looking
  8. cmp241

    Fault code 106?

    Hello everyone, One of the alarms listed is Fault code 106, The one having to do with faulty I/O board. I tried to administer the various test under the FIFTI command but it says my subsystem do not exist, when the system is either SYSDISK1, SYSBUFS11, OR SYSBUFS12,I tried all of these and it...
  9. cmp241

    Configuring Ethernert Port as MML Port

    Hello, Can someone please tell me how to configure the ethernet port on the NIU2 as a MML port? Thanks P.S. I am able to log on to the system now, we created our own V.24 to serial cable, lol.
  10. cmp241

    MD 110 Installation help needed

    Thanks for the insightful tip, I guess, we will start making our own cable for that, lol.
  11. cmp241

    MD 110 Installation help needed

    Here's a printout of what I see: To run a command as administrator (user "root"), use "sudo <command>". See "man sudo_root" for details. cedric@cs-linux:~$ telnet 10.210.15.32 Trying 10.210.15.32... Connected to 10.210.15.32. Escape character is '^]'. >login: sssssSSSSSSS; Login Rejected...
  12. cmp241

    MD 110 Installation help needed

    Also, as I asked before, but no one answered. Do I need another cable to start the MML session? All I have is the ethernet cable, I don't have the V.24 cable is this the problem? Thanks
  13. cmp241

    NIU2 IP ADDRESS?

    pcasi thanks for your suggestion, however you miss understood me I already have the ip address and do not wish to change it. I could login to the NIU2 board, but can't use any of the MML commands. If you reply, please do if you can, can you repy to my other post that talks about the same...
  14. cmp241

    MD 110 Installation help needed

    Dave thanks for your reply, I basically open up a unix terminal, and telnet to the NIU2 IP address, then I type SSSSSSS (with no ;) and the default username and password and i get the niux prompt. I also tried SSSSSSSS; and it still didn't work. Do it have to be a combination of lower and upper...
  15. cmp241

    MD 110 Installation help needed

    Alright, from my understanding there's two ways to start a MML session; via the IPU board with a special cable, through a cable with a serial port connection via the NIU2 unit, and via the NIU2 ethernet cable and typing in SSSSSSSSS;. I don't have the IPU board nor the serial cable, so our only...
See more

Part and Inventory Search

Back
Top