Recent content by cmorales

Thanks Randy, I understand the concept of the if statement, however, need to know how to actually create this field. Is this a calculated field. I've attempted to create one to no avail. thanks again.

I'm working on a MS Access database. I need to know how to create a field that outputs a result based on criteria from another field. Basically I have a field where a grade score will be entered. Based on this value, I want another field to display "Pass" or "Fail". Your help will be greatly...

thanks, that worked!

need a little guidance. I would like to create a date field that creates year only (2004) and automatically changes to 2005 to reflect new year. I'm sure this is pretty simple but I cannot figure it out

Thank you all for the information. The find & replace worked!

Need help deleting partial data from an excel field. Here is is my field... SSN 123-45-6789 SSN 123456789 I need to remove the hyphens from 500 records.

Actually this is the topology: [computers] -> [hub] -> [cisco] -> [Dlink] -> [internet] i have a default route on cisco pointing to Dlink: ip route 0.0.0.0 0.0.0.0 192.168.0.1

Cable Modem Router DLink 614+ (192.168.0.1) network 192.168.0.0 default gateway 192.168.0.200 (E0) Connected to Hub 192.168.0.1 192.168.0.2 192.168.0.100 Cisco Router 2500 (E0) 192.168.0.200 network 172.16.0.0 default gateway 172.16.0.1 (E1) Cisco 1900 switch (default configuration) 172.16.0.2...

is this picture clearer? Network / Default Gateway 172.16.0.0/16 192.168.0.0/24 DG 172.16.0.1 192.168.0.1 Cisco 2514 DLINK PC<--SWITCH<--[ e1 / e0 ]-->HUB-->ROUTER-->Cable .2 .1 .200 | .1...

correction on the Ehternet ports Network / Default Gateway 172.16.0.0/16 192.168.0.0/24 DG 172.16.0.1 192.168.0.1 Cisco 2514 DLINK PC<---SWITCH<---[ e1 / e0 ]--->HUB--->ROUTER--->Cable Modem .2 .1...

I implemented Rip v1 on the cisco router to no avail. I also added a static route to the cisco router. I can't add a static on the Dlink. Still cannot ping to any of the devices on opposite networks. Haven't tried this yet, but could the default gateway be an issue? Here the topology again...

Thanks for your advice... Let me try it. I will post results later...

Mesa, Network 192.168.0.0 default subnet mask: 255.255.255.0 default gateway: 192.168.0.1 (on DLink router) Network 172.16.0.0 default subnet mask: 255.255.0.0 default gateway: 172.16.0.1

IP routing is on. As Mesa states &quot;Turning on a protocol would not be of use in this case&quot; because the networks are directly connected. I do have a default gateway static address on router: ip route 0.0.0.0 0.0.0.0 192.168.0.1 Good question Mesa. I have a 10/100 Hub between the Dlink...

Here's my topology. DLink Router connected to Cable Modem LAN Network: 192.168.0.0 Default Gateway 192.168.0.1 Host 192.168.0.2 Host 192.168.0.3 The router above is connected to Cisco 2501 Router which has 2 Ehernet ports. E0 is part of network 192.168.0.0 E0 ip is 192.168.0.200 E1 is...