Recent content by clayfoxmvp

I currently have a Packet8 (like Vonage) voip adapter plugged into my analog port on an IPO403 3.1(56). The quality of the connection on both sides is great but often I am having an echo on the IP Office side on calls over this connection. At first I thought it was my IP Phones but it happens...

I am using Intuity mode so I guess that is it. Bummer. Clay

This is what I had at first as that is what I have always done. It will not even work with selecting Caller's mailbox, I still get the prompt for entering a mailbox number. The Leave works fine but something is up with the Get Mail. I even played with the *17 short code to see if it was...

I am trying to use an attendant for checking several mail boxes. On the Specific tab the help says that if the name of a mailbox is entered in the target field than that is the box otherwise a ? will allow the box to be selected. I have tried several different names but all go the "Welcome to...

Outgoing CLI used to work fine before version 2 with Assisted Transfers in VMPro. I would have a custom voicemail attendant that would have an option to do an assisted transfer to a phantom extension which was forwarded unconditional to a cell phone. Since version 2 this has stopped working...

You need to be careful and read the specs. I have found some that do not put out enough watts to power the 4600 IP phones. I went with Powerdsine which is kind of high end but can be reasonable on ebay and they put out a lot of power. Clay

I am cheap and I have several sites with extreme, since it is the corproate standard but it is all refurbished and/or used. I buy spares but I have paid probably 10% of what I would have paid new. I have had some issues from time to time but I think everyone has and the new equipment does not...

This makes sense because I see this often and have used Assisted Transfer in VMPro since 1.3. Assisted Transfer worked great for me to transfer to external cell phones. The original CLID went to the cell and then returned to the menu if there was no answer. With v3 up to version 3(44) the...

I have gotten this pop up window with Phone Manager since first version 3 and since then. I have XP with firewall off but still get it whenever the network connection to the IP Office resets. For instance on wireless and move out of range and then come back or when connecting the VPN connection...

I have never gotten fax detection to work on any incoming call route. Does this actually work? I have incoming call routes which route to the fax board as outlined above by kflounders, however with two different IPOs, each with a PRI, I have tried to route based on the call type but never...

I have had issue with SMMI transplants. I beleive if you access the boot prom and set the configuration back to default then move them that they will be willing to learn their new surroundings. I have not had a chance to test this yet but I know there is a way to get them to accept a new...

Hey Peter, I am currently trying to test the same thing. I am new to Extreme as well but now have 15 of them. I am not sure if the basic layer 3 has all the functionality or not. I know to do OSPF it needs the full layer 3. I tried to get OSPF working unsuccessfully but I did had RIP working...

I have set one up via an IP Trunk directly without a license which I beleive is for setting up IP extensions. I do not have one setup at the moment but I know I had to play a lot with the configuration. I setup some Ericsson gateways too, which I had to do two trunks, one for each direction...

I purchased LKA10 headsets to go with the 6416D+M phones and use the headset port without a lifter. However I only get them to pickup but I cannot get it to dial or pickup the DTMF tones. I can answer a call but cannot make a call. I press talk and hear the dial tone but then none of the...

Some of the reason is political and some is that the network is not always as realiable as they would like so this way they have a hardwired connection through to a PRI. Is there a way to limit the information output from the 403 to make it more friendly to the trunk loop start ICLID port...