Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by Class26

  1. Class26

    CLAN-BD Err 2817

    Thanks for your help. That did stop the phones from registering there. Unfortunately still getting error 2817 on our C-Lan but we will figure it out.
  2. Class26

    CLAN-BD Err 2817

    We are having an issue with one of our Clans. We recently removed most of our clan boards and are using the Procr for registrations now. But we still have a few in place. One for Ecas, one for Redsky and one for Modular. The board in question is the Modular board. It keeps showing an error 2817...
  3. Class26

    DAC/FAC changes

    This is more of a general advice question. We have to change our dial plan as we currently are using several numbers in the 1000 block for access codes. The change is pretty straight forward and we will simply be adding a 1 in front of the code and changing the dial plan to allow for 4 digits...
  4. Class26

    Trouble removing cabinet.

    Textron, Unfortunately I tried that and it doesnt help. Avayatier3, If it is software corruption, how do I go about resolving it? Reconnect the cabinet and then try to remove it? ( The port does not show up under list mark )
  5. Class26

    Trouble removing cabinet.

    I am having an issue removing an EPN. I have performed change circuit-packs and was able to remove all other equipment but have 1 TN2224 Digital line card that shows " " Must remove translation on the board before changing circuit pack type. There are no extensions assigned to this board as...
  6. Class26

    9620L issue

    Well, We discovered a solution. Ill write it in if anyone finds this at a later time. We had 2 seperate issues occuring, the one mentioned above getting Bad FileSv Address was an issue with our DHCP scope. There was an entry for DSN Domain name. The newer phones were searching only that...
  7. Class26

    9620L issue

    thread690-1569972 I am having what seems to be the exact same issue. We are using CM System: G3xV13 Software Version: R013x.01.5.642.3 I am trying release 3.1 on the firmware side but have also tried older releases and there is no difference. Basically a 9620 phone works perfectly...
  8. Class26

    96xx Phones not finding http server

    Thanks. We finally figured it out. We found some issues with the otpion 242 settings. Wrong range for IP's. We also removed the TLSSRVR= piece. We still had issues with the system not pulling a voice vlan ip but that was resolved by inserting an IPhelper address into the layer 3 switch I...
  9. Class26

    96xx Phones not finding http server

    Yes. That is part of what I am trying to do. I have placed the upgrade files on our httpserver and the phone would connect to the c-lan and let you insert an extension but would not seem to find the http server and get its updates or settings. When I statically assigned the http server...
  10. Class26

    96xx Phones not finding http server

    Are you talking about the phones Mitch?
  11. Class26

    96xx Phones not finding http server

    Upon further reading it appears I add in "HTTPPORT=81" but still not certain where exactly or if it matters. But since we are using phones that seem to be release 1.5 they will have to upgraded to 2.0 before they will even recognize the command... At least that is what I gathered from...
  12. Class26

    96xx Phones not finding http server

    Where exactly would that be programmed into the 242 if you dont mind me asking? Obviously I am not the one who wrote the option and I am a little ignorant in that area.
  13. Class26

    96xx Phones not finding http server

    Another thing to note. We have no issues with the 16xx phones. They find the file server fine. To verify I cleared all the settings and let it re-register through DHCP and it worked properly. Also a seperate question on the 96xx phones.. Can you still use commands such as (mute,v,i,e,w,#) and...
  14. Class26

    96xx Phones not finding http server

    I searched several posts and could not come up with a definite answer here so I decided to post my question and hopefully have it stated specifically. I am running Cm 3.1.5 We have a few hundred 16xx series ip phones and we are trying to install some 96xx series ip phones now as well. My...
  15. Class26

    IP connecting gateways

    Could someone give me a quick rundown on the step required to convert an EPN into ip connect. Currently. Our EPNs are connected with a ds1-c and exp-int card in each cabinet. I suppose it would require swapping out the maintenance board to a TN775D and adding an IPSI and Medpro card.... I was...
See more

Part and Inventory Search

Back
Top