Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by ciscopix77

  1. ciscopix77

    ISDN bonding problem

    Anyone?? [ponder]
  2. ciscopix77

    ISDN bonding problem

    Hi Thanks for the reply...I have checked the 3com website and unfortunately for me we have the newest version of the ios. I have tried it with one dialer, it works but ony allows access of one user at a time with 64k connection. I was hoping that more than one user can connect at a time (using...
  3. ciscopix77

    ISDN bonding problem

    Hi all I have a 3com router, but am hoping someone here would help me out with this problem. we have 3 isdn lines (2 channels each) and when I try to bind two isdn channels to get 128k of bandwidth, I can dial into the router and it says 128k connected, but nothing happens. I cannot browse the...
  4. ciscopix77

    ISDN bonding problem

    Hi all I have a 3com router, but am hoping someone here would help me out with this problem. we have 3 isdn lines (2 channels each) and when I try to bind two isdn channels to get 128k of bandwidth, I can dial into the router and it says 128k connected, but nothing happens. I cannot browse the...
  5. ciscopix77

    Migrating mreak mailserver from one server to another

    HI I was wondering if someone can point me in the right direction or if there is a tutorial about this online. Basically it is about migrating a merak mailserver that is on one server to another server in a different location. Is this easy to do? I would appreciate an advice. Many thanks
  6. ciscopix77

    Remote agent backup to external server

    Thanks for that! Do u know how I can do the manual install? I have read the instrucctions but not quite sure how to do it? I don't umderstand the part where it says to map the drive to a directory? Sorry for the silly questions! Thanks
  7. ciscopix77

    Remote agent backup to external server

    Thanks for the reply. We r using version 9.1. With regards to the ports being opened, where should I open these ports? Only on the remote server firewall? Or also on where the backup exec is installed (As it is sitting behimd a firewall as well). A bit confused! cheers
  8. ciscopix77

    Remote agent backup to external server

    Hi all I was wondering if it was possible to install remote agent on an external server with external ip address. I have tried and tried and veritas does not allow me. I have also allowed access thru our firewall for the remote agent (port 10000 TCP) on the external server but still get an...
  9. ciscopix77

    Pix NAT/PAT question

    Hi I have a question about the pix 506e PAT. I know u can use PAT to translate several internal IP's to one external one, but can u do the same if u had 2 external IP addresses to combine them to one internal ip address? Is that possible at all? Thanks
  10. ciscopix77

    Router ISDN question

    Hi It's me again!! Do u think I will still need this command at the start: ppp mp binding-mode authentication and this one in each BRI interface: ppp mp I'm asking because we no longer need to bind lines or this does not harm the config? cheers
  11. ciscopix77

    Router ISDN question

    You there? :) You probably are fed up with me by now...hehe... Just one last scenario, let's say there are 3 dialer interfaces, int dialer0,dialer1 and 2 using ip's 10.10.10.1, 10.10.11.1 and 10.10.12.1. But let's say the clients that dial in are on the 192.168.x.x subnet. My question is would I...
  12. ciscopix77

    Router ISDN question

    Just wanted to ask about hese lines: ip route-static 0.0.0.0 0.0.0.0 217.xxx.xxx.xxx preference 60 ip route-static 10.10.10.0 255.255.255.0 Dialer 0 preference 60 ip route-static 192.0.0.0 255.0.0.0 Dialer 0 preference 60 I should add the route for each subnet? e.g. ip route-static...
  13. ciscopix77

    Router ISDN question

    So for the first scenario nothing changes in the original config at all? Just a matter of testing it? and the second scenario just as u explained above! I think I got it...Finally! Will let u know how it goes...Very much appreciate ur responses! cheers
  14. ciscopix77

    Router ISDN question

    So would it look like this: interface Dialer0 link-protocol ppp ppp authentication-mode pap ppp mp ppp mp max-bind 6 ip address 10.10.10.1 255.255.255.0 ip address 10.10.10.2 255.255.255.0 ip address 10.10.10.3 255.255.255.0 ip address 10.10.10.4 255.255.255.0...
  15. ciscopix77

    Router ISDN question

    Hi again! When u say leave as it is, do mean as the original post? Just one dialer interface? Or try the suggested ip's (2,3,4) each with a separate dialer interface? A bit confused now...
See more

Part and Inventory Search

Back
Top