Recent content by CHRIN1

Dear eriuser, can you please tell me how to use NIU2 ? and which port to be use 1-0-xx-1 or ...other. can i use serial port that was previously use for SMDR out ? As the first programmation, IODDP; I/O DEVICE DATA NODE IODEV/SUBFS BPOS/EQU SIPOS TYPE/USAGE STATUS AUTH...

Dear all, My company is using MD 110 PBX. last month my NIU1 card burnt and i have to replace with NIU2. can anyone tell me the procedure how to process ? or i just remove the failure card and replace with the new one? anyway how to connect from NIU to PC if the previous card was lost...

Dear all, I am the new user on PANASONIC TD1232. these 3 days i met some problem with my CO line the red light on operator console was qucikly flashing with the remak CO2= CO 02 and ringing every 5 Mn. Can anyone help me to solve this matter because what i have did right now is removed the co...

Dear, i am the new user of PANASONIC TD1232 PBX. can anyone tell me how to disable CO ringing back ? I got this problem since the installation and it's so trouble. all extensions in my office ring from time to time. the display shows that CO = CO02 and blinking. thanks for your help regards,

Many thanks for your clearly explanation:-) Right now i alraday create new row ROU=2 with ED=7 coz 9 is set for operator:-(. in that time i had changed and blocked others extension too. with my regards happy new year.....

dear rfpui, I would answer your question G Q: because i need to have privat trunk (1-0-62-01) reserved for only ext 200 to 205. only this trunk that available for international call ( there are 20 number from pstn to my PBX and only 1 that can international access). An 1: the external line...

Dear, I am also a stupid guy on MD110 BC11, can someone hlp me how to fix extensions 200&&205 to only 1 trunk with equ=1-0-62-01 during route to external. Anyway my system got only 1 rou ROCAP:ROU=ALL; ROUTE CATEGORY DATA ROU SEL TRM SERV NODG DIST DISL TRAF 1...

Thanks alot for your advises now i can fix it Cheers Chrin1

Could someone tell me what is different between INDIVIDUAL and common code. and how to set individual code i already set my common code but i need to lock for each extension with diferrent password. Thanks

Dear, Now i can retrie all data to my PC but i still misunderstanding on <Cldfp; FILE ADMINISTRATION DATA FILE STATE SMDR01 ACT IODEV/PATH USER DEVICE STATE PRIORITY SMDR CIL-1 READY/STARTED C END Could you tell me when i disconnect the cable the device state...

Dear, I can't print the message SMDR out form my PABX (bc11sp08)at all event i try to check the command as belows: <cinip; COMMAND UNKNOWN <ioddp; I/O DEVICE DATA NODE IODEV/SUBFS BPOS/EQU SIPOS TYPE/USAGE STATUS AUTH SYS 001-0-60 - - IN SERVICE SYSN SYSDISK1...

Dear gedii, Ok thanks i will ask them to check but from PSTN i use analogue trunk lines ( 12 line) only. Just to tell you that when i direct call from PSTN the sound is acceptable but after entering in to PABX the sound was so low. Thanks chrin1

Dear all, Could someone tell me how to calculate hour. Thanks

Dear all, During call out the other party can't hear my voice clealy the sound is too low even i try to increase the phone volume. this matter appears only out going call but extionsion is normal. Does the MD110 bc 11 have the way to increase the volume. Many thanks chrin1

DEAR, I DO AS YOU HAVE SET LIKE THIS: ROCAI:ROU=2,SEL=712000000000001,TRM=4,SERV=2100000000,NODG=1,DIST=30,DISL=128,TRAF=03151501,SIG=211000000000,BCAP=001100; RODAI:ROU=2,TYPE=TL11,VARI=00000108,VARO=00002816,VARC=00000012,FILTER=NO;@/EXECUTED/...