Recent content by cfwdude

just make sure you turn off any Antivirus software before installing the service pack!! bad things otherwise!

just build thee new server - DO NOT add it to the domain, keep it in a workgroup. Make sure you install all of the same service packs and hotfixes that are on the old system, as well as applications, except for exchange. I was missing a few hotfixes, but they only applied to IE6, and Outlook...

My exchange server is a domain controller, but does not have the key management services running on it. There were a few addtional steps to consider if yours was. I will check my notes regarding this when i get ot my office. I will be moving another Exchange server, that is also a domain...

If you just want a new installation of Exchange, and are getting rid of the old one, or rebuilding it for another purpose, you can move everything to the new server, keep it's ip address an computer name, Active directory, everything. Build the new server, install exact same service packs and...

Few questions for you mkatzer, How long did your actual conversion take? What was the size of your Cam database? Are you still using the POSStar for the register software? Did you have to change you credit dard processing software? I am in a 5 store (5 databases) setup, each db at around 5G. We...

I somehow screwed up the lines on a couple of my phones and have been unable to reconfigure them. I cannot seem to delete a line. I have also been unable to do a line copy from a good extension to this one to clear up the problem. Is there anyway to reset a phone/extension to default?(blank)...

Thanks for the correction lgarner. Made the changes, still can't get to the public ip of the mail server. I am able to ping outside interface of ISP router, and outside interface of PIX, but cannot ping outside ip of mail server, or telnet to port 25. I am using a very similar config on a...

CiscoFrEaK, i added the Access list and removed the conduit statements. access-list 101 permit icmp any any echo access-list 101 permit icmp any any echo-reply access-list 101 permit tcp host 206.13.51.163 eq smtp any access-list 101 permit tcp host 206.13.51.163 eq www any access-group 101 in...

I am trying to test a mail server by telneting to it's public IP on port 25. Here is the hardware scenario: ISP - Cisco 1721 (config below) Public outside address, public inside address My Cisco PIX 501 (config below) Public outside, Internal address inside, NAT and static route to mail...

I have already added the internal address of the second cisco as the gateway for the second card. But when trying to telnet to port 25 on the public ip that is pointed to the second NIC, I get no response. I am able to ping external IP associated with 2nd NIC from ISP router, and ping to...

Anyone know how to remove a service? I have a Testbed server, that I have tested upgrading a POS database application (which failed). I have uninstalled the POS app, but the service remains, and cannot start. The problem is that I need to reinstall the old version of the POS app, which uses an...

C'mon guys! 1 Exchange server 2 NICS 2 ISP's providing T1's 1 MX record pointed to NIC1 (fully functional) Need to configure Exchange for 2nd NIC, 2nd ISP, only as far as being able to telnet to port 25, and send authenticated mail. (MX record to soon be pointed to this NIC) ?? suggestions ...

I am currently running Exchange 2000, and we have had a second T1 installed. I have configured a second Cisco PIX device NAT'ing to the internal IP of my Exchange server, (has 2 NIC's, 2nd T1 to 2nd internal ip.), and have port 25 open as well. Here's the question, Can I just add the second...

I am running CamCommerce RetailStar 6.41, with 4 retail locations, and am looking for an upgrade. I have had consistent stability issues with the DB, and Cam's support isn't that great. I also have limited info for running Crystal Reports off the database, since the canned report feature is...

We have recently added a second office to our company, and I have set up a frame connection between the two offices. now I need to allow for my home users to access the new subnet via thier PIX 501 vpn connection to a 515e. Main office 10.0.0.x New office 10.0.1.x home user 192.168.2.x The...