Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by centoffsuper

  1. centoffsuper

    call pilot 100/150

    Ok, thanks. From what I am reading, I will need to first change my format from two digit ext. to 3 digit? I can set up hunt groups on the KSU and then just use the leading ext. as the ext. to point the CCR path to So on the call pilot itself, i need to set it up as transfer, intercom...
  2. centoffsuper

    call pilot 100/150

    I am trying to set up a call pilot ccr on a norstar cics. If i am using the ccr setup in the call pilot is it possible to make 2 or 3 extensions rings at once. For example, I want it to say "press 1 for parts" then parts will ring on ext 42 and 43..the next is "please press 2 for all other...
  3. centoffsuper

    cisco asr1001-x

    Hi I am trying to set up netflow and ip accounting on this router asr1001-x 3.14.01. I had been using a 3945 and had no trouble with either. Does anyone have the procedure to do this? I was thinking cef needed to be on and then go to the interface config and type ip flow monitor...And for the...
  4. centoffsuper

    Cisco 3845 level 15 privilege show run command shows nothing

    Thanks everyone for your comments. Not sure what happened but the running config is showing up again...weird.
  5. centoffsuper

    Cisco 3845 level 15 privilege show run command shows nothing

    yes i can do most everything else. when i do a show tech-support the running-config is also empty there. almost like it was erased but the startup-config is still in place. when i log into the router i have always used telnet with the exception of a few times where i would console. i used the...
  6. centoffsuper

    Cisco 3845 level 15 privilege show run command shows nothing

    All of the sudden my router is not showing the running config. I have verified that I am at level 15 when I try. Any ideas? Thanks.
  7. centoffsuper

    next step 100mbps plus

    Hi I have a dsl, metro e, and wireless network that is all running through an Adtran NetVanta 1238 then one enet cable to 0/1 on a Cisco 3845 router which in turn goes out on 0/0 to a cisco Cisco ME 3400G-2CS with another enet cable which in turn goes on out on fiber to where we get our 100mbps...
  8. centoffsuper

    port forward to 8080

    Hello this might already have been answered but we are a small isp and a subscriber asked me if I would (in my main internet router which is a cisco 3845) port forward his public static ip to port 8080 so he can remotely monitor some equipment. Any ideas on the best way to do this? Or is this...
  9. centoffsuper

    new install MICS 7.1 most station ports have trouble

    Just to update I shut down the system and booted back up without the 2 port extender card, when set 221 said cold restart i powered down again (without a cold restart) and re installed the card. Then I powered back up and so far all extensions but one are working...so.........I dont know what to...
  10. centoffsuper

    new install MICS 7.1 most station ports have trouble

    229, 235 thru 242 and 244 thru 252 and as near as I can tell all the ports on the station module I plugged in. The voice mail is on port 243 and it is working good so far. Thanks
  11. centoffsuper

    new install MICS 7.1 most station ports have trouble

    this system does have an expansion module for a 12x0. If this system was turned on before plugging in the fiber for the 12x0 would that cause this sort of problem? I have 10 extensions and 8 incoming lines that are working great. I even have the CP150 up and running but those other station ports...
  12. centoffsuper

    new install MICS 7.1 most station ports have trouble

    Yeah I tried that. I tried different cables and everything. I even put a different cabinet in but used the existing software cartridge and had the same results after it booted up. Is it possible the software is corrupt? So far that card is the only thing common. Thanks
  13. centoffsuper

    new install MICS 7.1 most station ports have trouble

    Hey all, I have a refurb MICS 7.1 with cp150 that i setup over the last three weeks at my office and it worked great. I moved it today to permanently install it at the customers and now half of the stations do not work. If you plug a t7316 into a station port it will instantly flash red at a...
  14. centoffsuper

    Norstar Call Pilot 150 ccr help

    I have a business that wants their customer to be able to dial 1 for emergencies, 2 for sales, 3 for..etc......in the emergency box they are wanting the caller to be able to leave a message and then the on call tech will be paged from that mailbox. Then after the tech is paged he can call in...
See more

Part and Inventory Search

Back
Top