Recent content by cbum

Hello, Yes, the problem sounds like a Fritz card problem. The reason I asked for a Debug of "ppp" was to find out if it was Multilink PPP compatibility ( or Fritz setup) issue between the Cisco and the Fritz card. cbum

Identifying a Rollover Cable You can identify a rollover cable by comparing the modular plugs at the two ends of the cable. When you hold the plugs side by side, with the tab at the back, the wire connected to the pin on the outside of the left plug should be the same color as the wire...

Hello. Debug's didnt show anything helpfull. Are you using the same Username and Password when testing with 800 and the Fritz card ?. Also, lets take another approach. Run "debug ppp negotiation", "debug ppp authentication" "debug ppp error" and "debug...

Hello. The problem is not with the method. NVRAM means that the initial configuration for that interface came from NVRAM. This is a sample config I would try. First I would change Serial interface to "encapsulation HDLC" on both Cisco Routers. HDLC is less complex to setup...

Hello. question 1) The Cisco 800 connect with 2 channels to the 3640 ?. question 2) The ISDN Fritz card will only connect with one channel to the 3640, the Fritz card is using the same ISDN line as the Cisco 800? If the answer is YES to both, then you will need to run DEBUG on the...

Hello, I just did a test on my Laptop with nothing connected to the Serial COM port and ran Hyperterminal and it showed "connected", so "connected" means nothing ( I just learned that today ). Also compare the RJ45 cable ends, the wires will be rolled. example =======...

Hello. I have had this same problem many times, I use WINDOWS 98, Hyperterminal 9600 baud, 8 data bits, no parity, and 1 stop bits, flow control "none". The only other problem would be the cable between the Laptop (pc) and the Router Console port. The cable I have is light Blue...

Hello, hard to say without knowing your configuration from the two Routers. If you decide to post the configuration's please make sure you remove passwords / usernames , descriptions , telephone numbers, etc. cbum

Hello, Maybe this will help. http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis2600/2600hig/2600inst.htm ====================================== Connecting to the Console Port To connect a terminal (an ASCII terminal or a PC running terminal emulation software) to the console...

Hello. You can use AAA accounting feature to record Cisco AS5200 activity and more. Go to this URL. http://www.cisco.com/univercd/cc/td/doc/product/software/ios113ed/113ed_cr/secur_c/scprt1/scacct.htm http://www.cisco.com/univercd/cc/td/doc/product/software/ios11/cbook/csysmgmt.htm hope...

Hello. For the 2621, the Documentation states that. -----------------Cisco--------------------- Sync support with a max speed of 2.048 Mbps Supports one port at 8 Mbps when used in NM-1FE1R2W, NM-1FE2W, NM-2FE2W, or NM-2W or 2600 chassis WIC slots. All other WIC ports on that network...

Hello. Take a look at the URL below, it shows how to setup exec and enable password ( the Cisco 675 and 678 use the same command's). http://www.cisco.com/warp/public/794/675login.html Complete documentation at...

Hello. Please take a look at Cisco Documentation at the following web site. http://www.cisco.com/univercd/cc/td/doc/pcat/sewn__y2.htm Look at the Hardware Specifications. The WIC-2T and WIC-A/S are supported on the Cisco 3600 (on the NM-1FE2W, NM-2FE-2W, NM-2W, and the NM-1FE1R2W network...

Yes NAT will work with secondary addresses on the inside and there should not be anything complex to configure here as you will configure the NAT access-list to allow just the primary or secondary or both to pass through the NAT. Example: ip nat inside source list 1 interface serial0...

Hello Fadi. I dont know why the Ping is not working from Cisco to Lucent. Ping from Cisco to its own interface may not work, the packet needs to leave the interface and comeback in for this to work. I would need to see the configuration to understand why Cisco cant ping the Lucent...