Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Recent content by CBRRyda
-
Client to Router VPN driving me nuts
JPF, I'm having a somewhat similar problem with my Cisco 1811W and VPN IPSEC using the Cisco VPN Client. Can you explain in more detail your statement, "Using a route map to prevent traffic from my internal lan to be natted between the VPN lan did the trick." I'd greatly appreciate it. Thank... -
Cisco 1811 VLAN and Routing Questions
vbahuse, Did you mean the SDM (Security Device Manager) for the 1811 Router config? I think the CNA is for configuring the switches. I too, am trying to get VPN Clients to connect to devices on VLANs defined and connected to my Cisco 2960 switches; which are trunked to the 1811 of course. Does... -
Cisco 1811 VLAN and Routing Questions
vbahue, Thanks for inquiring. I have all of my VLAN and Routing issues taken care of. I am however, still working on my VPN IPSEC setup, have not quite got that working correctly yet. I will also be looking at any posts to the thread. Regards, CBRRyda -
DSL on Cisco 1811W
Thanks brianinms and burt; brianinms, when I try to add the second (ip nat inside) to the config, I get the following error: "%Dynamic mapping in use, cannot change" burt, what commands should I use to encrypt the telnet, enable, and console passwords? Thanks All. -
DSL on Cisco 1811W
Ok All, sanitized version of config below: ------------------------ cisco1811w#sh run Building configuration... Current configuration : 7003 bytes ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname cisco1811w ... -
DSL on Cisco 1811W
Thanks Burt, I'll have to try the unplug T1 access after hours and see what happens then. I'll let you know. -
DSL on Cisco 1811W
One more question, Can you add a second Cisco config line: ip nat inside soure list 10 interface FastEthernet1 overload Without the second line interfering with the existing equivalent line but on FE0 for NAT\PAT? Thanks Again. CBR -
DSL on Cisco 1811W
I ordered and installed DSL at my office location, as a backup to our existing T1 WAN connection. I have setup, configured, and tested the DSL connection, it works. Our T1 access is connected to my router's FE0 port, the DSL is connected to the FE1 port, as a DSL Ethernet handoff. I have... -
Cisco 1811: VPN using PPTP with MPPE
Hello All, Newbie here again. Does anyone have a working sample config or example, of a Cisco 1811 Router using VPN over PPTP with MPPe. Thank you in advance for any assistance. -
Cisco 1811 VLAN and Routing Questions
All, I now have the Cisco 1811W. I am trying to do the following: 1. Create 3 VLAN's for: LAN1, LAN2, and Wireless 2. Route between the VLAN's and to Internet 3. Configure some of the ports on the Router for specific VLAN's; FE4-5 VLAN11, FE6-9 VLAN12 4. FE2-3 are Trunk Ports to connect... -
Cisco 1811 VLAN and Routing Questions
All, I'm a newbie and in charge of upgrading our existing VPN and routing solution. I'm looking at the 1811 w\wireless and had some questions: 1. If you separate FE2-5 ports to VLan1 (IP x.x.1.1), and FE6-9 to VLan2 (IP x.x.2.1) for local inside subnets; does the router support DHCP Relay...
