Recent content by Cawho

The problem I am experiencing is that I have some 6140 handset that fall into a coma state after not being used (they are idle attached to belt) when they go out of range of the WLAN. When I come to use it, it is not working, it display the extension number twice its size in the display, no...

It is MGCP, the interface card is a DT24+, and don't know what "binding q.931 to ccm via backhaul support" is... sorry I noticed incoming calls and out going calls are using ports 23 and down. How can ports 1 and up become locked out if they aren't used. I have to find what device uses the ports...

I have setup a PRI between, a 61C-PBX from Nortel and a CCM release 3.3. it is working fine but some channels are being LockedOut in the PBX, the first few members. When calls go out, CCM uses bottom up, so it must be from calls coming in. My route in the PBX is a TIE route. And I used a DTI24...

I have 3 route patterns, One is for internal phones on a different system 2XXX The othe is 9.XXXXXXX for people who dial 7 digits ANd the last is 9.@ for 10 digit dialing. But what happens is that the Call Manager waits for more than 7 digits and that timer is 15 seconds to long. I can't find...

No it is not just the MWI being lit later. The person who reported it to me is my IT support. I trust her, she told me she took her messages when she got in, (1 message). Then 5 minutes later, 6 messages (earlyer messages than the first one) was in her voice mailbox. it was reported to me from...

What would make my UNITY server deliver voice messages 1 hour later than it should? Thanks Cawho PBX.Tech

I'm sorry, it works here, I am going out on a digital route, maybe you are not and it dials the 9 to fast, try to input the whole number as HOT D 10 95143708787 and see if you get a different result, try with an internal number to see what result you get. Let us know, Cawho PBX.Tech

Did you have to add CLS=EHTA ? Cawho PBX.Tech

Don't worry about the xlst. what is the SCH-code you are getting? Cawho PBX.Tech

Yes but that is right because the call is from conferenced from the mail until someone answers. if no answer then goes to his voice mail. I think it has to do with the mail TNs. I don't know the answer but maybe I point you in the right direction... Cawho PBX.Tech

The way I do it is like this: DES My modem doesn't dial 9 to get out. TN 125 0 10 11 TYPE 500 CDEN 4D CUST 0 DN 2008 0 MARP CPND NAME . XPLN 5 DISPLAY_FMT FIRST,LAST AST NO IAPG 0 HUNT TGAR 1 NCOS 1 RNPG 0 XLST 3 CLS CTD DTN FBD XFD WTD THFD...

Here is how I would do it: (without moving from my chair) Check the CDR records (internal and external) and would filter each DN to see if it is used or not. I would have to check everyday for a month. Then: Call the numbers left to see if someone answers or if a device answers, I would do...

I know I am suprised also, I am actually trying to compare with my system, and I also get "translation" from I don't know where yet.... but I count on finding it. I'll let you know ASAP. I got the same results as you but IDC says no in the RDB so I am looking elsewhere there is some...

.trad 68 8 ACTIVE TN 068 08 DIRECT MW_CALL ORIG 068 08 WATS RMBR 200 8 TERM 024 0 11 10 0 ACD 0 1619 2616 DIAL DN 3928 MAIN_PM ESTD TALKSLOT ORIG 15 TERM 13 JUNCTOR ORIG7 TERM7 EES_DATA: NONE QUEU NONE CALL ID 0 5131 ---- ISDN PRA CALL (ORIG) ---- CALL REF # =...

I think the 103 of 1038999 would be info (let's say NCOS) of the incoming trunk? would that make sense? Cawho PBX.Tech