Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by buang

  1. buang

    HiPath 3000 Trunking (Need Help)

    Dear Master, I have 3 unit HP3800 on workshop and planned for interconnection using IP trunk using HG board. Extension already mapped 1xxx for A, 2xxx for B, 3xxx for C. I try searching over google to get IP trunking documentations for HP3800 but not found, most documents for HP4K. Any suggest...
  2. buang

    AC Win installation error (Need Help)

    Problem solved. I need to install AC_Win first then license. We need to install Microsoft visual redistributable 2005, 2008, 2010, JRE 6update11, .Net Framework 4 extended and .Net Framerowk client. Thanks for your attention
  3. buang

    AC Win installation error (Need Help)

    Hi everyone, Need help once more. :-D I just installed AC Win software on Win 7 Professional genuine. Step by step that i dids is install CLM(license management) OK. Install CLA(license agent) OK. Install AC Win failed that error message attached. that is error messages during installation...
  4. buang

    ATNDIND with access code 0. Need Help

    the PSTN line is OK. tested finally it case solved with reinstall Hipath 4000v6 software and reconfigure from the beginning. so confuse about this problem.
  5. buang

    ATNDIND with access code 0. Need Help

    Can we ignored an attendant feature and focus to configuration how to get outgoing line with access code "0"? Because my latest configuration below is not successfull to get outgoing line when i dialed "0". When i dialed "0" there is error message on OpenStage 15T diplay "Currently not...
  6. buang

    ATNDIND with access code 0. Need Help

    Hi everyone, anybody help me. I just configure an attendant for hipath 4000v6. I try to create an outgoing line with TMANI module. This is step by step configuration. Add-wabe:0 as CO Add-wabe:9 as atndind Add-buend:100 as TGRP Add-tacsu:devtype:TMANIMSG Add-richt Add-ldat Add-ldpln And result...
  7. buang

    Hipath4000v6 - TMANI Configuration(Need Help)

    Problem resolved. We need to change PTIME parameter (see Hipath4000v6 documentation). Try to change cha-ptime:tmanimsg,13, see on PARA parameter The value is just example for indonesia PTIME. P5 : 12 P6 : 65 P11 : 6 P12 : 0 P13 : 0 P14 : 16 Thanks all of your advice Buang M. Yulianto
  8. buang

    Hipath4000v6 - TMANI Configuration(Need Help)

    everything in the system sound O. Only the TMANI trunk sound bad. The status board is READY (checked in DIS-BCSU:TBL,1,1,6;) and status of the trunk is READY (checked in DIS-SDSU:ALL,,PEN,PER3,1,1,6,0;). And i try DIS-ZAND:CONFC; the parameter is ULAW and i try to change to ALAW parameter and...
  9. buang

    Hipath4000v6 - TMANI Configuration(Need Help)

    In indonesia.
  10. buang

    Hipath4000v6 - TMANI Configuration(Need Help)

    Hi everyone, anybody help me. i had configure TMANI module on Hipath4000v6. Here is my latest configuration. I have a flow chart to configure it, is this correct? WABE : Create CO access Code BUEND : Create TGRP TACSU : Assign configuration to TMANI module RICHT : Create route LDAT : LDPLN ...
  11. buang

    Hunt Group with SIP extensions on Hipath 4000 v4

    May be you can use this AMO ADD-AUN.
  12. buang

    Hipath 4000 v6 + OpenStage 40 SIP (Need Help)

    Currently the configuration is finished and working good.(see my last configuration post). Thanks for your advice at all. Thread Closed Thanks in advanced Buang M. Yulianto
  13. buang

    Hipath 4000 v6 + OpenStage 40 SIP (Need Help)

    Here is my last configuration update. I try to applying as you suggested. Is this correct? After this configuration has created ,there is same problem as before. An error message on display "unable to select an outgoing line". Thanks in advance...
  14. buang

    Hipath 4000 v6 + OpenStage 40 SIP (Need Help)

    this is my last configuration to activate OpenStage 40 SIP. But there is error message unable to select an outgoing line on the OpenStage display. Im using STMI4 modul ADD-BFDAT:2,SIP,BCHL60&BCHL120,; CHA-BFDAT:CONT,2,SIP,10,,1; CHA-BFDAT:OK,2,YES...
  15. buang

    Hipath 4000 v6 + OpenStage 40 SIP (Need Help)

    i'll try to delete all existing configuration and reconfigure it. waiting for my last update. thanks for your advice
See more

Part and Inventory Search

Back
Top