Recent content by Bostik

I have set up a new Backup Exec 9.1 environment on a new Windows Server 2003 machine and it's working great. However the notes say that when I install the Exchange agent, I also have to install the Exchange admin console. I still have Exchange 5.5, and cannot install this console on server 2003...

We have the same situation with Notes 5.0.5. You need to enable the smtp service on one of your notes servers, do this in the server doc in the address book under basics: SMTP listener task: Enabled

I am trying to import some MIB's into Compaq Insight Manager 7 Sp2.3, I can send them to the server so that they are in the 'unregistered mib's window, but when I try and register I get the error Cannot find module SNMPV2-SMI How do I get round this?

I have a W2K SP1 server running terminal services and 12 clients, all running W2K Professional expect for 1 crappy old Windows 95 box which I cannot upgrade. I recently purchased some new Epson C70 printers, all attached locally to each PC. They all work fine in TS apart from the Win 95 box...

I have two servers running W2K server and services for netware 5. Both servers are on the same IP network separated by a router. The router is IPX enabled and both servers are on the same IPX internal & external network numbers. However these two servers cannot see eachother IPX-wise. I've...

We run File and Print services for netware v 5 on one of our W2K servers. We have a small problem that when we reboot the server, any netware shares which we have set up disappear and we have to re set them up. Mac and Windows shares are not affected. Apart from applying FPNW Service Pack 1 or...

We're having problems selectively restoring the registry on NT machines. The backup job shows 'registry' as a separate session for each NT machine and 'system state' for each W2K machine. However when we try to restore part of a registry, the W2K machines show up fine on the 'restore by...

I've just found the solution to this problem on CA's crappy Open Forums: I made changes to the registry: HKLM\Software\ComputerAssociates\ArcserveIT\Base\TapeEngine Created a key name 'Config' then added a value 'EnableSharedDevices' type REG_DWORD, value of 1 Stopped and restarted the tape...

After applying SP3, I can no longer see any autoloader slots under the device. I use an HP Surestore autoloader with an ultrium-1 drive, and the tape library option. The strange thing is, Device Config can see the slots fine and i can allocate a cleaning slot. It's only in Arcserve Manager...

I had the same problem until I added full control rights for the Arcserve system account to the Arcserve share on the system drive. Arcserve set up this share, and rights for local backup operators etc, but didn't do the same for the specified Arcserve system account. I also found that...

I have an NT4 print server with 250 shared network printers installed. I've built a replacement new server with Windows 2000 Server installed - does anyone know of an easy way to copy print queues from old server to new without me having to setup 250 new print queues on the new server? I need to...

Well I've been through all the servers and checked that everything is hard-coded to 100Mb/s Full duplex. I'm still gettings <40Mb/min on the servers. I did a test backup of a whole W2K server to a different server on the same network. This was also using Arcserve 2000 host, but I did the backup...

We run Notes 5.0.5 on site an have Win 95, NT and 2000 clients. About 6 months ago, *all* the Win 95 clients started having a Notes startup problem. When Notes is launched, the splash-screen appears, disappears and that's it - notes does not run. We found that if we disconnect the network drive...

We're experiencing slow backup speeds (only about 40Mb/min) and when you have >400Gb to back up, it takes a while... We have a HP surestore ultrium library (single drive, 9 slot) and Arcserve 2K SP2. When I applied SP3, I could no longer see my Ultrium slots under device - the drive contents...