Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by blaksplash

  1. blaksplash

    how to change logo.sys in xp?

    the file that the boot logo is in, is \windows\system32\ntoskrnl.exe you may have to get the file off the cd, or if you have sp1 you'll need to get that version since it was updated in sp1. when you get the original file, go into safe mode to restore the file.
  2. blaksplash

    Divix Movie Files - URGENT!

    can you see them from a command prompt? if so, they may have done an alt255 trick. this makes the first character blank and i belive it makes them invisible to older windows OS'es. while holding alt type 255 then the filename to delete it or whatever if this is the case. ex. del...
  3. blaksplash

    8600 supply default route

    now i just need to figure out how to get another 1200 to send a default route to an ARN...
  4. blaksplash

    8600 supply default route

    got it working... had to make an announce policy to announce static and bgp routes. it seems that bgp was the one i needed in there.
  5. blaksplash

    8600 supply default route

    We have a Passport 8606 and a XLR1200. The 8606 is set up as the core and the 1200 is the remote. The 8606 has RIP turned on globaly and enabled with RIP supply, listen, default supply, and triggered updates on the VLAN. The 1200 has RIP enabled globaly and RIP supply, listen, default listen...
  6. blaksplash

    Burn A VideoCD...HOW?

    kwunder, according to the VCD specs, it is. If your DVD player supports SVCD (480x480 & 720x480, MPEG2) you might want to try that route. But, I have found that with my DVD player, if i burn a VCD in Nero but use a MPEG2 video file @ 720x480 it will play, kinda. I say kinda because the video...
  7. blaksplash

    Syslog & ARN

    you have to be consoled into the ARN to perform this 1.Power cycle the ARN. 2.When the ARN starts cycling through Power On Diags, type Ctrl C followed by a carriage return. This will put you in diagnostic mode and you will see the following prompt: Diag_1> 3.At this prompt, type in the...
  8. blaksplash

    Motherboard upgrade question?

    here is what i would do make sure you have ALL your drivers for your components! boot to safe mode right after the new hardware is installed. In safe mode, go to device manager and remove EVERYTHING. reboot and it will find all your hardware including your new motherboard settings. you will...
  9. blaksplash

    Passport 8600 Trunking with Comapq server

    do your two NICs have to have the same MAC address? in order to use MLT they must share the same MAC address.
  10. blaksplash

    Installing 98 "AFTER" W2k... Possible?

    Also, the c: drive HAS to be FAT or FAT32, because win98 can't read NTFS to put it's boot files there. If the c: drive is NTFS, it will have to be converted.
  11. blaksplash

    Can PC150 RAM be used on a PC100/133 board?

    Cirrus9 is correct, as long as it is the same type the motherboard accepts (ie 168 pin DIMM) the speed of the RAM must be at least the speed of the bus of your motherboard.
  12. blaksplash

    Can't connect to internet from IE in WIN nt4...

    first thing i would do is try to ping a domain name like www.yahoo.com or www.tomshardware.com to see if your gateway and DNS settings are correct. if that is succesfull, it may be the settings for IE. Goto tools > internet options > connections tab > LAN settings in IE and setup your proxy if...
  13. blaksplash

    Syslog & ARN

    update- i got it working i had to put a wildcard filter in there, set up the severity mask for warning, info, critical, and trace. i also had to put slot lower bound as 1 and upper bound as 1.
  14. blaksplash

    Installing 98 "AFTER" W2k... Possible?

    I haven't tried it with boot magic, but these are the instructions i used (I did have to convert the root c: partition from NTFS to FAT32 with partition magic): This configuration will work ONLY if the root partition is FAT16 or FAT32 and the partition on which you install Win98 is also FAT16...
  15. blaksplash

    Syslog & ARN

    does anyone know how to set up an ARN router to send events to a syslog server? I tried setting it up on one but with no success. The server DOES work because I have an Accelar 1200 sending events and it is recieving them fine. The settings i have put in using site manager are: Global...
See more

Part and Inventory Search

Back
Top