Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations bkrike on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by beybros

  1. beybros

    BCM and Micom

    We install a new BCM 400 3.7 with two T1s. The first T1 (bus 7- line 61-84) is working fine. Our second T1 is connected to a Micom unit. This DSXI port on the Micom unit is set up like a t-1. When we connected a t1 cross cable this solve half our problem (remote sites can call the home office)...
  2. beybros

    windows XP pro

    I am unable to completely uninstall Norton systemworks. I was installing a new antivirus software when I receive a message informing me of my old software. I did a search and found the software, so I try to delete it. I receive a message stating access denied. Any suggestion?
  3. beybros

    T-1 Problem

    We replace our cat5 cable with a T1 cross cable and change line pool. KNOW, we are able to dial 8 and receive dial tone. After we dial the 8 then 45/70/etc.,we do not hear any tones but are able to see the digits accross the screen. Any suggestions?
  4. beybros

    CCR TREE TO VOICE MAIL

    I setup a CCR Tree with a transfer node to VM #. I am unable to make this work. I replace the VM # with other numbers, this does work. Is their something else I must do or a new approach?
  5. beybros

    After hours, DID goes to GenDeliveryMbox

    morgansdad, I am having problems setting up my DIDs to ring on our phones. Will give me your lay out? Thanks
  6. beybros

    Programming DID'S

    I have no AA on line 241+. The if busy field is set to prime and prime set is set to their extension.
  7. beybros

    Programming DID'S

    I did not setup any ring services
  8. beybros

    Programming DID'S

    This was already done stephenwyker from the beginning.
  9. beybros

    Programming DID'S

    acewarlock, In fact I took off AA on line 61 rhur 84. When I call one of the DID numbers I receive a message from the BCM voice mail(this mail box is not initialize and can not accept any message), but if I dial the DN after the VM recording play. I can reach there voice mail box and leave a...
  10. beybros

    T-1 Problem

    good ideal thanks
  11. beybros

    T-1 Problem

    I deprovision 8 lines 91-98. when we dial 8 the system tell me no free lines. How can I fix this?
  12. beybros

    Programming DID'S

    Our AA answers each time someome call a DID number
  13. beybros

    T-1 Problem

    I set the absorb length to zero.We used numbers like 845 and 817 to reach the different sites.
  14. beybros

    T-1 Problem

    We install a new BCM 400 3.7 with two T1s. The first T1 (bus 7- line 61-84) is working fine. Our second T1 is connected to a Micom unit. This DSXI port on the Micom unit is set up like a t-1. Just to let you know we switch from an Option 11 c to BCM 400 and the set was working fine. This is...
  15. beybros

    Programming DID'S

    We have a DN range from 300 TO 332. Our DID blocks are 1300s and 1500s. We would like these calls to ring on the assign target lines. OH, we have AA also. Taking Advice.... Thanks
See more

Part and Inventory Search

Back
Top