Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by bequi

  1. bequi

    Problem with Fallback on BCM

    snowman50: Thanks for the answer, we have tried it, but the result is the same. I changed the control set, even i deleted all DN on "Line pool A" (the Bri's Pool), but if you link down the LAN, you can call with BRI. SupportDude: Thanks. Yes i'm sure, even i deleted all DN from "Line Pool A"...
  2. bequi

    Problem with Fallback on BCM

    We have a problem with a Fallback on BCM50 (R2 and R3). Well, i'm not sure that be a problem, or a "philosophy of design". I have a BCM50 with 2 Voip trunks, and a "BRI MBM". The routing and scheduling is configured correctly. I have 1 emergency extention (emergency DN), and that should be...
  3. bequi

    BCM Backup to BCM

    Sorry i'm not work with 1.0 version. But if nortel has fixed on version 2.0 (april 2008), is possible that they had fixed on previous version. Thanks for you answer, and good luck ;) .
  4. bequi

    BCM Backup to BCM

    foneman1, we have the same problems with partial loss of configuration. You could see if you have installed the BCM050.R200.112-CORE-2.1-1.1 or later? (The version of Core-tlephony should be 42.03.18.8 or higher) On readme of the patch you can read: "1. Partial loss of Telephony Programming...
  5. bequi

    BCM 3.6 Speaking Spanish

    I think that you have this problem with the initialization porcess: http://www.tek-tips.com/viewthread.cfm?qid=1446781 Regards.
  6. bequi

    Lost telephony configuration on BCM50

    Hello everyone. Our costumer have some BCM50 working. Yesterday, a BCM50 has stopped to work and they can't send o recieve calls. The telephony configuration have been cleared. The BCM has the default configuration. (Like you had applied the "cold reset telephony services"). On the logs, we...
  7. bequi

    SmartUpdate 011

    You only need SU.system.11. 160-SoftwareManagement is included inside. (I have never needed apply previous SU.system) When you try upload the patch, will show a screen with two patches (su.11 & 160-SoftwareManagement). Select 1160-SoftwareManagement, and apply. Later, upload again Su.11 and...
  8. bequi

    can't ssh BCM

    Sorry, is the only way that i know. "so this is a BCM50/200 limitations..." I think so.
  9. bequi

    Adding a 32 DSM to BCM 400

    I think that the configuration and the DSM are OK. However, you need conect someone phone to see the bus active. When i don't have any phones conected, i see on MBM: Bus 02 - > Unequipped And when i conect some phones: Bus 02 - > Enabled The BCM don't detect if the DSM is conected. The BCM...
  10. bequi

    can't ssh BCM

    I only know a way to get a "Nortel pass": Asking to nortel technical support. When i have got a "Case", they bring me the password of the day (is relationated with Unique ID) to generate some special logs.
  11. bequi

    can't ssh BCM

    You only can access with "Nortel Pass" Is the same on BCM50 See this thread: http://www.tek-tips.com/viewthread.cfm?qid=1419126
  12. bequi

    Can not connect to Unified Manager after BIT Tool Imaging

    We have test the solution "Steps to take if you are already in a failure mode" of the bulletin "2008008624, Rev 1" and after follow the steps of guide, the UM is working fine.
  13. bequi

    Can not connect to Unified Manager after BIT Tool Imaging

    Nortel has posted 2 documents for this issue: Document: BCM 3.7 Software Upgrade Timer Expiration BULLETIN ID:2008008582, Rev 2 PUBLISHED 2008-01-29 http://www116.nortel.com/pub/repository/CLARIFY/DOCUMENT/2008/04/023305-01.pdf And inside a Top Issues: BCM / SRG / BCM50 Top Issues BULLETIN...
  14. bequi

    Can not connect to Unified Manager after BIT Tool Imaging

    Hello, we had the same problem. We tested the MagnaRGP solution, and it's working fine (THANK YOU VERY MUCH, MagnaRGP). We have Nortel BIT Tool refered NTAB9962. Do you have the same? Someone know if exist a newer BIT's version?
See more

Part and Inventory Search

Back
Top