Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Recent content by bberryca
-
New to 6500 Series
Hello, I was hoping i could get some help, I have a couple of 6500 series switches and i am looking for someone to give me a base config of what i should ensure i program. I have spanning tree enabled and all my blades are 48port 10/100's and i am running sup2's. pretty basic Layout with 10 or... -
6513 with ws-x6148-45af showing not supported
Yah its my IOS Version, and the Flash Size. I need to Get a 64mb Pcmcia Card and upgrade to 12.2 Thanks, Brad -
6513 with ws-x6148-45af showing not supported
Hello, I have bought a 6513 and one of the blades is a ws-x6148-45af its comming up "not supported" when i slot it. i've checked the IOS version and it says it need 12.1 min and i am running 12.2. Here is a dump from the switch ( i've removed the sn's.. Sorry if thats a issue): Router#show... -
OSPF Redunant Routers Quesiton
Correct,fully redundant, dual 1841's dual 2950's dual lan connections, and eventually dual telco gear connecting to separate pop's.(but thats down the road and will not effect my configuration) -
OSPF Redunant Routers Quesiton
Hello, I have uploaded a pdf of my layout, any help you can provided would be appreciated. Thanks, Bradhttp://www.mediafire.com/?thgldniya30 -
OSPF Redunant Routers Quesiton
Hello All, Any help i can get on this would be appreciated. So i have 6 sites with 6 10mb point to point links in a ring topology. Each point to point link has two ports provided by the telco. at each site I have 2 2950's and 2 1841's. every site is laid out the same, each site has two point... -
-
OSPF with Redundant Routers
Oh i guess i should mention that all my routers are essentially connected with point to point links provided my the telco, and are going to be ABR's. Site A and Site C are going to also have Internet connections. -
OSPF with Redundant Routers
Hello All, I have another question for you all, I am implementing multiple sites with redundant 1841's and redundant links the layout is SITE A <-> SITE B <-> SITE C <-> SITE D <-> SITE A All links will be 10mb how do i configure OSPF to work with dual routers ? I have give each link... -
-
2950-1841config questions
Thank you, i should have removed that before i posted the config, i couldnt make upmy mind what ip range i wanted the switch on. my issue main steams from the errors im getting when i have to interfaces on two different vlans connected to the same switch. is there away to stop the port from... -
2950-1841config questions
Hello, I am currently trying to set up a new branch location, i am wondering if my desgin will work and what the config should be. so here is the design, my provider is giving me 2 lan extensions (point to point 10mb) and then giving me 4 ports on a switch they are providing ( 2 on one lan ext... -
Rate Limit Question
Thank you very much, this worked perfect. regards, Brad. -
Rate Limit Question
Hello, I currently have a rate limit on one of my interfaces on a 1841, i want to modify it to not limit ftp traffic from a specific IP. here is the current setup: interface FastEthernet0/0 ip address 10.0.1.2 255.255.255.0 rate-limit input 3144000 16000 24000 conform-action... -
Network Design Question
Hello, we are in the planning process of over hauling our network, and i was wondering if i could get some feed back on the design. 9 call centers, 2 admin sites. currently all running vpn tunnels over the internet to tie the sites together. (this is a huge issue) note: i inherited it this...
