Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by b9dvator

  1. b9dvator

    UDP Software

    hello Kevin Again thank you for your assistance. What i have are non consecutive DID's, some of which i want to direct over a line side PRI w/QSIG enabled, to another PBX (non Avaya), , With the G3, i can leverage the UDP table (UDP routing first)to send the inbound call to an AAR table which...
  2. b9dvator

    UDP Software

    hello Kevin thank you for the quick reply, one additional question if i may, , can i use short codes on a per extension basis? thank you again for your assistance b9dvator
  3. b9dvator

    UDP Software

    Does the IP Office 412 support UDP software? In the G3 Switch and above, there is a UDP table where I can setup UDP routing first? If UDP routing is not supported in the basic 412 software package, is it a purchasable module? Thank you for your assistance! b9dvator
  4. b9dvator

    Tandem trunking on Magix

    hello Merlinman, many thanks for the information and the gotcha's, this is exactly what i was hoping for, , , thanks again b9dvator
  5. b9dvator

    Tandem trunking on Magix

    hello Merlinman, i dont know enough about the magix system, can you give me a little more insight about the above mentioned configuration. . . . thanks b9dvator
  6. b9dvator

    Tandem trunking on Magix

    hello All, At what release did the Magix system support tandem trunking or trunk to trunk transfer capabilities? I'm trying to support a trial for mobility which requires a PRI connection from the Magix and tandem trunking capability. thanks b9dvator
  7. b9dvator

    Paging system

    hello Todd1019, sorry to hear it costed you additional coinage, but glad to hear you found a resolution to you issue take care b9dvator
  8. b9dvator

    Paging system

    hello Todd1019, if you were able to get the headset to work prior, the next test i would do is, take the physical handset associated with that auto-answer telephone and plug it into the base unit of the M12 on the backside of the unit and test for audio there as well, (the jack is used for...
  9. b9dvator

    Paging system

    hello Tod, i have done simular things with the M10 / M12 base unit , , , lets eliminate a few troubling items, , is the unit battery powered or do you have the power supply to go with the unit, , , batteries don't last very long and observe polarity on the batteries. there are many varibles...
  10. b9dvator

    Beep tone generator when monitoring calls

    I have used DynaMetrics TLP-107 which inserts the beep and has a volune control. . . easy to connect to just about any phone model. . . somewhat inexpensive $80 b9dvator
  11. b9dvator

    EC 500

    thank you dwalin. . . this is great info . . . looks like i will need the upgrade after all to take advantage of the increased feature set . . . . thanks again b9dvator
  12. b9dvator

    EC 500

    What is the minimum sotware release required on the definity to support the EC 500, I've searched the previous messages, but to no avail thanks b9dvator
  13. b9dvator

    Question regarding 9600 and tandem trunking

    hello Perv2, thanks for the reply, it is very much appreciated. the requested configuration from the Fujitsu is a PRI to the mobility server, so we won't be using loop start trunking,can you think of any other potential gotchas? many thanks again b9dvator
  14. b9dvator

    Question regarding 9600 and tandem trunking

    hello to All i am trying to deploy a mobility server for an executive trial. i have a fujitsu 9600 R12, does anyone know if this release supports tandem trunking or trunk to trunk transfers. thank you in advance d9dvator
See more

Part and Inventory Search

Back
Top