Recent content by atdawgie

Thanks.

Hi, I'd like to create a drag and drop list of items using javascript but only want one user to be able to make changes to it, but allow all others to view it. Is this possible? Also is there a good or easy way to add and delete items from a drag and drop javascript list? Thanks, Aaron

But the problem is which router will the machine receive an IP address from? When a client computer comes online both routers race to give it a DHCP address. Both routers and computer are on the same physical network but I wont to separate them into logical networks if possible to prevent this...

I'm not sure I understand you? There are no ip's on the WAN side. It's all LAN-based.

HI! I have two routers. The RV042 and the WRT54G v 6.0. Each router has one computer connected to it. The two routers are connected to each other with a switch. The RV042 is configured with the IP 192.168.0.1 and the WRT54G is configured with the IP 192.168.1.1 Each router can be pinged...

Basically the problem is no matter what I do, I can't ping and get a reply from either computer. On the 192.168.0.0 I add the route to the router: route add 192.168.1.0 mask 255.255.255.0 192.168.1.100 192.168.1.100 is the other computer, there is no router. On the 192.168.1.100 computer...

Hi, Why doesn't this command work? What should the syntax be or is just not possible for these two networks to communicate? route add 192.168.0.126 mask 255.255.255.0 192.168.1.100 destination computer is at 192.168.0.126 source computer is at 192.168.1.100 error: the route addition failed...

Do you mean even if I set two static routes DHCP traffic won't cross over to the other network? I have one router 192.168.0.1 in gateway mode which hosts the internet connection. The other is 192.168.1.1 in router mode where I'm trying to get it to see the 192.168.0.1 router but I can't seem...

Hi, I have two routers on two subnets 192.168.0.0 and 192.168.1.0. Both are running DHCP. I added a static route between the two routers so clients can talk to each other. How do I make sure that DHCP traffic doesn't cross subnets? I don't want a client on subnet 192.168.0.0 to receive a DHCP...

Hi, I followed your instructions but it still results in the same problem. I can't use GPMC because I have windows 2000. Is there another tool I can use to see what policies are set or what area in group policy might be causing this? We are not running a proxy server.

Hi, I was able to change the recording announcement so when a person presses the shortcut, the announcement is made "this call will be recorded for training purposes" and they are able record the conversation. But it seems to be a system wide recording. Is there any way to change it so group A...

I replaced the file that sounds the most like the one played on the recording but it doesn't change anything. Is there a way to figure out which file it is, or is there a tool to change the wav file?

Okay, my short code is now *56*N# I place a call to 7305 through another phone, then I go to 7304 dial the extension *56*7305# and I get "call rejected" on my display and bzzzz on the phone? Same behavior as I had before. Anything else that it might be?

Thanks, I removed 7304 from the group and made sure only 7304 has the monitor option. I don't understand the shortcode info? The help file says add it as say *56*N# where N is the extension number I dial. If I add the SC as just 8999 and have a preset TN of 8999, how would I dial the...

Hi, I want to be able to record calls for training purposes but want to change the default system message from "warning this call is being recorded" to "This call is being recorded for training purposes" but don't see that option anywhere to make that change. Any clues? Thanks, Aaron