Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by Arr

  1. Arr

    CICS External Call Forward problem

    Alworx, Curly, Already went to MBX ext transfer using 7. Was hoping to by-pass the mbx step. An external speed dial button when programmed with F71, F78 xxx xxx xxxxx F78 F71 can't be used in conjunction with F4. Doesn't matter if a route is specificed or Intercom. I now suspect it is because...
  2. Arr

    CICS External Call Forward problem

    Hi Curly, All, I finally got beck to site today. A whole wac more time in on the problem leads me to think it is simply not possible to do the way I want. The process as described by MR in the FAQ works fine but uses two CO loops until the call is over. OK if there are lots of lines...
  3. Arr

    CICS External Call Forward problem

    Curly, Either you had too much Bailey's or too little - I can't tell... Indeed it is an MR FAQ: https://www.tek-tips.com/faqs.cfm?&rat1=10&fid=2078 Followed to the letter.... almost apparently. I'm really thinking you nailed it right off in your first reply - in that I used the...
  4. Arr

    CICS External Call Forward problem

    Curly, ah. See your point. Perhaps I was conflating two procedures. I did not try without adding "intercom". Darn. Rusty. I was not using # but inserting F71 which then displays the special character for Link. All is... well? Out west. Remodeled myself into an alternate energy weenie. But have a...
  5. Arr

    CICS External Call Forward problem

    Wow it's been a long time since I've posted here. Glad this site is still up and vibrant!! Situation: Norstar CICS Rel. 6.0 unexpanded Call Pilot 100 3.1 2xCLID trunk cards 12 sets 10 are M7310's Rls 16 or better IATA unused Four copper loop CO's incl 3 line overline & single loop w/real...
  6. Arr

    CP 100 PCMCIA Card?

    Yeah. Seen that a lot. First thing I did was replace the power supply. Then proved the power supply on a CP150. It was fine. Thanks for the thoughts. PhM "..second star to the right and straight on 'till morning.." VVV
  7. Arr

    CP 100 PCMCIA Card?

    Thanks for the vote of confidence. I'll give that a try. Cheers "..second star to the right and straight on 'till morning.." VVV
  8. Arr

    CP 100 PCMCIA Card?

    I've got a dead CP 100. It was a complicated setup. Does anyone know what programming might be retained by moving the old PCMCIA card to a new CP100? I've been away from this for a bit. Thanks PhM "..second star to the right and straight on 'till morning.." VVV
  9. Arr

    Redirect incoming calls to an external number

    It Lives - YES! Hopefully forgotten, but certainly not gone. Work in the off-grid energy sector now. Cheers Curly. Yank Disconnect Supervision or DS is adjusted in Configuration -show/next- (running from memory) Lines -show- then scroll to Supervised Y/N Must be done on all lines in the...
  10. Arr

    Redirect incoming calls to an external number

    Tokenyank, Have you allowed Redirect on the extention? B. Capabilities - set abilities - show - enter set ext no. - scroll down @14 nexts - redirect = Yes Must be set or line redirection won't work. Arrrrrr "..second star to the right and straight on 'till morning.." VVV
  11. Arr

    Redirect incoming calls to an external number

    Wow old info sure gets lost fast... Line redirection is good to go on an 824 and 616DS and 308DS Host signalling transfer or "hookflash" transfer is only good on ICS Rls 4.1 and higher like Curly rmembered. Like Marv says set lines for supervision; then on the phone to be used as the forward...
  12. Arr

    Startalk AA problem

    ... and I think it is a DN that hasn't got a mailbox set up... such as the IATA which everyone forgets about when a CICS goes default the ext (37?) then rings on line one and two.. ?? Cheers Arr "..second star to the right and straight on 'till morning.." VVV
  13. Arr

    DTMF Signalling While on a Call?

    Thanks for that. Cheers Arr "..second star to the right and straight on 'till morning.." VVV
  14. Arr

    DTMF Signalling While on a Call?

    It's been noted on some BCM's (no pattern identified) that while on an established call using DTMF signalling from the dial pad doesn't work. Is this a BCM setting or a Nortel Feature? Thks Arr
  15. Arr

    Lost All Companion BStns

    I rather suspect some smart business will buy up Norstar and then take it where it should have gone instead of that bloated thing they call BCM. Arr "..second star to the right and straight on 'till morning.." VVV

Part and Inventory Search

Back
Top